Kyocera TASKALFA 300I Скачать руководство пользователя страница 120

Страница: 120 / 408

2K5

1-3-84

U901

Checking/clearing copy counts by paper feed locations
Description

Displays or clears copy counts by paper feed locations.

Purpose

To check the time to replace consumable parts. Also to clear the counts after replacing the consumable parts.

Method

1. Press the start key. The counts by paper feed locations are displayed.

When an optional paper feed device is not installed, the corresponding count is not displayed.

Clearing

1. Select the counts to be cleared.

CASETTE 3 and CASETTE 4 cannot be cleared.

2. Select the counts for all and press [ALL CLEAR].
3. Press the start key. The counts is cleared.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

U903

Checking/clearing the paper jam counts
Description

Displays or clears the jam counts by jam locations.

Purpose

To check the paper jam status. Also to clear the jam counts after replacing consumable parts.

Method

1. Press the start key.
2. Select the item. The screen for selecting an item is displayed.

Method: [Count]

1. Select [Count]. The count of jam code by type is displayed.

Codes for which the count value is 0 are not displayed.

2. Change the screen using the cursor up/down keys.
3. Select the counts for all jam codes and press [ALL CLEAR].

The individual counter cannot be cleared.

4. Press the start key. The count is cleared.

Method: [Total Count]

1. Select [Total Count]. The total number of jam code by type is displayed.
2. Change the screen using the cursor up/down keys.

The total number of jam count cannot be cleared.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Display

Description

MP TRAY

MP tray

CASETTE 1

Cassette 1

CASETTE 2

Cassette 2

CASETTE 3

Cassette 3 (optional paper feeder)

CASETTE 4

Cassette 4 (optional paper feeder)

DUPLEX

Duplex unit

Display

Description

Count

Displays/clears the jam counts

Total Count

Displays the total jam counts

Содержание TASKALFA 300I

























































































































































































































































































































































































































Результаты поиска

Содержание TASKALFA 300I

Отзывы:

Похожие инструкции для TASKALFA 300I

Бренды по названию

Популярные бренды

Kyocera TASKALFA 300I, Руководство по обслуживанию

Результаты поиска

Содержание TASKALFA 300I

Отзывы:

Похожие инструкции для TASKALFA 300I

Бренды по названию

Популярные бренды