manualshive.com logo in svg

Kyocera TASKALFA 300I, Руководство по обслуживанию

Kyocera TASKalfa 300i - мощное многофункциональное устройство для офиса. Вы можете скачать бесплатно сервисный мануал для этого устройства на manualshive.com. Получите подробное руководство по обслуживанию и настройке устройства, чтобы обеспечить его долгий срок службы и бесперебойную работу.

Поделиться
Скачать
background image

2K5

1-4-51

(4) Network Twain error codes

(5) Software trouble error codes

Code

Display

Remarks

Causes

Check procedures/corrective measures

2202

Error: Network transfer with 
timeout

Response is not returned 
from the server above speci-
fied time.

Check the network connection (cable. net-
work condition within LAN, etc.).

9181

Error: Page max count over

The number of pages of a 
send file exceeded 999 
pages.

Set the number of pages as 999 or less.

Code

Display

Remarks

Causes

Check procedures/corrective measures

5101

Error: Not yet connected

Operation handle error.
Error for stored status in the 
operation handle.

Turn the main power switch off and on.

5102

Error: Already connected

Operation handle error.
Error for stored status in the 
operation handle.

Turn the main power switch off and on.

5103

Error: Not yet opened

Error for stored status in the 
operation handle.

Turn the main power switch off and on.

5104

Error: Already opened

Error for stored status in the 
operation handle.

Turn the main power switch off and on.

7101

Error: Memory Allocation

Insufficient memory space.

Turn the main power switch off and on.

7102

Error: Socket Create

Unable to create a communi-
cation socket.

Turn the main power switch off and on.

720f

Error: Unknown error

Unable to determine the 
cause.

Turn the main power switch off and on.

Содержание TASKALFA 300I

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TASKALFA 300I

IBM 3130 Planning Manual preview
3130
Бренд: IBM Страницы: 112
Canon UFR II User Manual preview
UFR II
Бренд: Canon Страницы: 149
Canon G650 Getting Started preview
G650
Бренд: Canon Страницы: 60
Lanier LD116 Quick Manual preview
LD116
Бренд: Lanier Страницы: 4
TallyGenicom 2440 Quick Start Manual preview
2440
Бренд: TallyGenicom Страницы: 38
Tally T8024 User Manual preview
T8024
Бренд: Tally Страницы: 266
Konica Minolta bizhub C227 Installation Manual preview
bizhub C227
Бренд: Konica Minolta Страницы: 12
Output Technology EuroLine Series Operator'S Manual preview
EuroLine Series
Бренд: Output Technology Страницы: 73
Xerox WorkCentre Pro 416 User Manual preview
WorkCentre Pro 416
Бренд: Xerox Страницы: 470
Oki C9600 Series Disassembly & Reassembly Procedures preview
C9600 Series
Бренд: Oki Страницы: 45
Kyocera FS-2100D Quick Installation Manual preview
FS-2100D
Бренд: Kyocera Страницы: 24
3nStar PPT205 User Manual preview
PPT205
Бренд: 3nStar Страницы: 8
Kyocera KM-2560 Service Manual preview
KM-2560
Бренд: Kyocera Страницы: 392
Ricoh PRSPC342DN1 User Manual preview
PRSPC342DN1
Бренд: Ricoh Страницы: 120
QMS qms-ps 800+ User Manual preview
qms-ps 800+
Бренд: QMS Страницы: 188
Sinfonia Technology DP-1045 Operation Manual preview
DP-1045
Бренд: Sinfonia Technology Страницы: 41
NEC PC-8000 Series User Manual preview
PC-8000 Series
Бренд: NEC Страницы: 90
Epson Epson Stylus NX330 Service Manual preview
Epson Stylus NX330
Бренд: Epson Страницы: 63

Бренды по названию

Популярные бренды

Загрузить еще бренды