manualshive.com logo in svg

Kyocera TASKALFA 300I, Руководство по обслуживанию

Kyocera TASKalfa 300i - мощное многофункциональное устройство для офиса. Вы можете скачать бесплатно сервисный мануал для этого устройства на manualshive.com. Получите подробное руководство по обслуживанию и настройке устройства, чтобы обеспечить его долгий срок службы и бесперебойную работу.

Поделиться
Скачать
background image

6

Vérification de l’image sur le DP

Veillez à effectuer le réglage en procédant dans l’ordre suivant. Sinon, il sera impossible d’obtenir un réglage correct.

Pour vérifier l’angle du bord avant, reportez-vous à la page 7.

<Valeur de référence> Copie recto seul: ±3,0 mm max.; copie recto verso: ±4,0 mm max.

Pour vérifier l’angle du bord arrière, reportez-vous à la page 10.

<Valeur de référence> Copie recto seul: ±3,0 mm max.; copie recto verso: ±4,0 mm max.

Pour vérifier l’agrandissement, reportez-vous à la page 14.

<Valeur de référence> ±1,5% max.

Pour vérifier la synchronisation du bord avant, reportez-vous à la page 16.<Valeur de référence> ±2,0 mm max.

Pour vérifier la ligne médiane, reportez-vous à la page 18.

<Valeur de référence> Copie recto seul: ±2,0 mm max.; copie recto verso: ±3,0 mm max.

Lorsque vous utilisez l’original pour effectuer le réglage, vous pouvez effectuer automatiquement le réglage de l’agrandissement, de la synchronisation du bord avant et de 

la ligne médiane en une seule fois.

Pour le réglage automatique en utilisant l’original pour effectuer le réglage, reportez-vous à la page 20.

Checking image from the DP

Be sure to adjust in the following order. If not, the adjustment cannot be performed correctly.
For checking the angle of leading edge, see page 7.

<Reference value> Simplex copying: within ±3.0 mm; Duplex copying: within ±4.0 mm

For checking the angle of trailing edge, see page 10.

<Reference value> Simplex copying: within ±3.0 mm; Duplex copying: within ±4.0 mm

For checking the magnification, see page 14.

<Reference value> Within ±1.5%

For checking the leading edge timing, see page 16.

<Reference value> Within ±2.0 mm

For checking the center line, see page 18.

<Reference value> Simplex copying: within ±2.0 mm; Duplex copying: within ±3.0 mm

When using the original for adjustment, automatic adjustment of magnification, leading edge timing and center line can be performed at a time.
For the automatic adjustment using the original for adjustment, see page 20.

Verificación de la imagen del DP

Asegúrese de ajustar en el siguiente orden. De lo contrario, el ajuste no puede hacerse correctamente.
Para verificar el ángulo del borde superior, vea la página 7.

<Valor de referencia> Copia simple: dentro de ±3,0 mm; Copia duplex: dentro de ±4,0 mm

Para verificar el ángulo del borde inferior, vea la página 10.

<Valor de referencia> Copia simple: dentro de ±3,0 mm; Copia duplex: dentro de ±4,0 mm

Para verificar el cambio de tamaño, vea la página 14.

<Valor de referencia> Dentro de ±1,5 %

Para verificar la sincronización del borde inferior, vea la página 16. <Valor de referencia> Dentro de ±2,0 mm
Para verificar la línea central, vea la página 18.

<Valor de referencia> Copia simple: dentro de ±2,0 mm; Copia duplex: dentro de ±3,0 mm

Cuando utilice el original para el ajuste, puede hacerse un ajuste automático del cambio de tamaño, sincronización del borde superior y línea central al mismo 
tiempo. Para el ajuste automático utilizando el original para el ajuste, vea la página 20.

Überprüfen des Bilds vom DP

Die Einstellung in der folgenden Reihenfolge durchführen. Anderenfalls kann die Einstellung nicht korrekt durchgeführt werden.

Angaben zur Prüfung des Winkels der Vorderkante auf Seite 7.

<Bezugswert> Simplexkopie: innerhalb ±3,0 mm; Duplexkopie: innerhalb ±4,0 mm

Angaben zur Prüfung des Winkels der Hinterkante auf Seite 10.

<Bezugswert> Simplexkopie: innerhalb ±3,0 mm; Duplexkopie: innerhalb ±4,0 mm

Angaben zur Prüfung der Vergrößerung auf Seite 14.

<Bezugswert> Innerhalb ±1,5 %

Angaben zur Prüfung des Vorderkanten-Timings auf Seite 16.

<Bezugswert> Innerhalb ±2,0 mm

Angaben zur Prüfung der Mittellinie auf Seite 18.

<Bezugswert> Simplexkopie: innerhalb ±2,0 mm; Duplexkopie: innerhalb ±3,0 mm

Bei Verwendung des Originals für die Einstellung können die automatischen Einstellungen für Vergrößerung, Vorderkanten-Timing und Mittellinie gleichzeitig durchgeführt 

werden.

Angaben zur automatischen Einstellung mithilfe des Originals auf Seite 20.

Controllo di immagine dal DP

Verificare che la regolazione avvenga nel seguente ordine. Altrimenti, la regolazione non potrà essere seguita correttamente.

Per controllare l’angolo del bordo principale, vedere pagina 7.

<Valore di riferimento> Copia simplex: entro ±3,0 mm; Copia duplex: entro ±4,0 mm

Per controllare l’angolo del bordo di uscita, vedere pagina 10.

<Valore di riferimento> Copia simplex: entro ±3,0 mm; Copia duplex: entro ±4,0 mm 

Per controllare l’ingrandimento, vedere pagina 14.

<Valore di riferimento> Entro ±1,5%

Per controllare la sincronizzazione del bordo principale, vedere pagina 16. <Valore di riferimento> Entro ±2,0 mm

Per controllare la linea centrale, vedere pagina 18.

<Valore di riferimento> Copia simplex: entro ±2,0 mm; Copia duplex: entro ±3,0 mm

Quando si utilizza l’originale per la regolazione, la regolazione automatica dell’ingrandimento, della sincronizzazione del bordo principale e della linea centrale possono 

essere eseguiti contemporaneamente.

Per la regolazione automatica eseguita con l’originale, vedere pagina 20.

<< 图像确认 >>

必须按照以下步骤进行调整，否则不能达到准确调整的要求。

·确认前端倾斜度  第 7 页

< 标准值 > 单面 ：± 3.0mm 以内、双面 ：± 4.0mm 以内

·确认后端倾斜度  第 10 页

< 标准值 > 单面 ：± 3.0mm 以内、双面 ：± 4.0mm 以内

·确认等倍值  第 14 页

< 标准值 > ± 1.5％以内

·确认前端定时调整    第 16 页

< 标准值 > ± 2.0mm 以内

·确认中心线  第 18 页

< 标准值 > 单面 ：± 2.0mm 以内、双面 ：± 3.0mm 以内

使用调整用原稿功能时，可以同时自动进行等倍值、前端定时以及中心线的调整。

·通过调整用原稿进行自动调整   第 20 页

<< 画像の確認 >>

必ず下記の順序で調整を行うこと。順序通りに調整を行わない場合、

正しい調整ができない。

・先端斜め確認　7 ページ

＜基準値＞ 片面：± 3.0mm 以内、

両面：± 4.0mm 以内

・後端斜め確認　10 ページ

＜基準値＞ 片面：± 3.0mm 以内、

両面：± 4.0mm 以内

・等倍度確認　14 ページ

＜基準値＞ ± 1.5% 以内

・先端タイミング確認　16 ページ

＜基準値＞ ± 2.0mm 以内

・センターライン確認　18 ページ

＜基準値＞ 片面：± 2.0mm 以内、

両面：± 3.0mm 以内

調整用原稿を使用すると、等倍度調整、先端タイミング調整、センターライン調整の自動調整が一度におこなえる。

・調整用原稿による自動調整　20 ページ

Содержание TASKALFA 300I

























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TASKALFA 300I

Saxxot CRU-158 Operation Manual preview
CRU-158
Бренд: Saxxot Страницы: 13
DASCO EBS-260 Cleaning Procedure preview
EBS-260
Бренд: DASCO Страницы: 2
quadient DS-200iQ User Manual preview
DS-200iQ
Бренд: quadient Страницы: 130
Wang 2241 Reference Manual preview
2241
Бренд: Wang Страницы: 24
Lexmark X748dte Product Specification preview
X748dte
Бренд: Lexmark Страницы: 2
Lexmark X860 Brochure & Specs preview
X860
Бренд: Lexmark Страницы: 8
Ricoh SP C250SF Settings Manual preview
SP C250SF
Бренд: Ricoh Страницы: 4
Xerox VersaLink C400V User Manual preview
VersaLink C400V
Бренд: Xerox Страницы: 196
Xerox WorkCentre Pro 32 Specification preview
WorkCentre Pro 32
Бренд: Xerox Страницы: 14
Variquest Perfecta 2400STP Assembly Instructions Manual preview
Perfecta 2400STP
Бренд: Variquest Страницы: 12
Oce VarioLink 2650cp Quick Setup Manual preview
VarioLink 2650cp
Бренд: Oce Страницы: 2
DNP DP-DS80D Startup Manual preview
DP-DS80D
Бренд: DNP Страницы: 33
Ricoh SP 213Nw Setup Manual preview
SP 213Nw
Бренд: Ricoh Страницы: 23
Oki MC560 Plus User Manual preview
MC560 Plus
Бренд: Oki Страницы: 239
Xerox WorkCentre 5845 Quick Reference Manual preview
WorkCentre 5845
Бренд: Xerox Страницы: 14
Riso MZ790U Instruction Manual preview
MZ790U
Бренд: Riso Страницы: 266
Epson EPL-N2050 Setup Manual preview
EPL-N2050
Бренд: Epson Страницы: 55
Epson ES-300C User Manual preview
ES-300C
Бренд: Epson Страницы: 123

Бренды по названию

Популярные бренды

Загрузить еще бренды