Kyocera TASKALFA 300I Скачать руководство пользователя страница 56

Страница: 56 / 408

2K5

1-3-20

U030

Checking motor operation
Description

Drives each motor.

Purpose

To check the operation of each motor.

Method

1. Press the start key.
2. Select the motor to be operated.
3. Press the start key. The operation starts.

4. To stop operation, press the stop key.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

U031

Checking switches for paper conveying
Description

Displays the on-off status of each paper detection switch on the paper path.

Purpose

To check if the switches for paper conveying operate correctly.

Method

1. Press the start key.
2. Turn each switch on and off manually to check the status.

When a switch is detected to be in the ON position, the display for that switch will be highlighted.

*: Optional.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Display

Operation

MAIN

Main motor (MM) is turned ON

FEED

Paper feed motor (PFM) is turned ON

EJECT(FW)

Eject motor (EM) is turned on clockwise

EJECT(REV)

Eject motor (EM) is turned on counterclockwise

DRUM

Drum motor (DRM) is turned ON

Display

Switches

FEED1

Feed switch 1 (FSW1)

FEED2

Feed switch 2 (FSW2)

FEED3

Feed switch 3 (FSW3)

MP TRAY

MP feed switch (MPFSW)

REGIST

Registration switch (RSW)

EJECT

Eject switch (ESW)

BRANCH

Feedshift switch (FSSW)

DUPLEX

Duplex paper conveying switch (DUPPCSW)

JOB SEPARATOR

Job separator eject switch (JESW)*

Содержание TASKALFA 300I

























































































































































































































































































































































































































Результаты поиска

Содержание TASKALFA 300I

Отзывы:

Похожие инструкции для TASKALFA 300I

Бренды по названию

Популярные бренды

Kyocera TASKALFA 300I, Руководство по обслуживанию

Результаты поиска

Содержание TASKALFA 300I

Отзывы:

Похожие инструкции для TASKALFA 300I

Бренды по названию

Популярные бренды