KYMCO ADG5 Скачать руководство пользователя страница 49

Страница: 49 / 426

2.Periodic Maintenance XCITING S 400

Throttle Free Play

Inspection

Check the throttle cable free play by gently rotating the throttle grip back until

resistance is felt.

Throttle grip free play

2 ~ 6 mm

Make sure the throttle moves smoothly and returns on its own. Start the engine and

let it warm up. Turn the handlebars from side to side, if the engine rpm changes

either the free play is too small or the throttle cables are not routed properly. Check

and correct the cause.

Adjustments of the throttle free play can be made with the cable adjusters below the

grip throttle.

Loosen the throttle cable adjuster lock nut and turn the adjuster to achieve the

specified free play.

When the free play has been moved into specification hold the adjuster in place and

tighten the locknut securely.

Resistance First Felt

Closed

Adjuster lock nut

Adjuster

9-29

Содержание ADG5











































































































































































































































































































































































































































Результаты поиска

Содержание ADG5

Отзывы:

KYMCO ADG5, Руководство пользователя, Страница: 49 / 426

Результаты поиска

Содержание ADG5

Отзывы: