KYMCO ADG5 Скачать руководство пользователя страница 47

Страница: 47 / 426

2.Periodic Maintenance XCITING S 400

Engine Compression Test

SAFETY FIRST: Protective gloves and eyewear are recommended at this
point.

Remove the under cowl set. See the external topic for more information.

Before testing the compression make sure the cylinder head bolts are tightened

securely and the valve clearance is specification.

See the Cylinder Head and Valve Clearance topics for more information.

Remove the spark plug. See the Spark Plug topic for more information.

Thread a compression tester into the spark plug hole hand tight. Hold the throttle all

the way open. Crank the engine with the starter motor until the needle on the gauge

stops rising. Do not crank the engine more than a few seconds.

Cylinder compression

15 kg/cm

Low compression is an indication of excessive engine wear, possibly worn rings or

poorly sealing valves, or maybe a tight valve with not enough valve clearance. High

compression is possibly an indication of excessive carbon buildup on the piston or

performance modifications.

9-27

Содержание ADG5











































































































































































































































































































































































































































Результаты поиска

Содержание ADG5

Отзывы:

Похожие инструкции для ADG5

Бренды по названию

Популярные бренды

KYMCO ADG5, Руководство пользователя

Результаты поиска

Содержание ADG5

Отзывы:

Похожие инструкции для ADG5

Бренды по названию

Популярные бренды