KYMCO ADG5 Скачать руководство пользователя страница 420

Страница: 420 / 426

15.EEC System

XCITING S 400

Function

Item

Function

Description

Evaporative

Emission

Control Valve

It is used to prevent gasoline

vapors from escaping into the

atmosphere from the fuel tank

and fuel system.

Storage the gasoline vapors to

canister, conduct the gasoline

vapors to engine by vacuum

when starting the engine.

Canister

Storage the gasoline vapors

from fuel tank and fuel

system.

The gasoline vapors storage by

canister, to meet the regulation,

the HC emission con not exceed

2 grams.

P.C.V

Recycle the fuel gas from the

crankcase blow by.

Recycle the fuel gas from the

crankcase blow by to the engine.

Oxygen

Sensor

To control the air/fuel mixture

in best condition.

Sending the mixture condition

info to ECU by voltage signal,

ECU control the fuel injection to

meet the emission regulation.

Catalyst

To reduce the emission of HC,

CO and NOx produced from

the exhaust gas.

Using the catalyst convert the

HC and CO to oxygen and

reduce the NOx pollution.

ECU

To control the injector, ignition

and bypass air of fuel

injection system to reach the

best driving condition.

ECU (Electric Control Unit),

receiving sensor which equipped

on engine to precisely control

fuel injection and ignition to

reduce the exhaust emission

pollution.

Trouble Shooting

Low engine power, instable engine idle speed



Clog in canister or tubes.



Emission control valve malfunction.



E.E.C. system tubes loosen or crack.



ECU malfunction.

Engine idle speed and acceleration in bad condition



Clog in canister or tubes.



Emission control valve malfunction.

14-3

Содержание ADG5











































































































































































































































































































































































































































Результаты поиска

Содержание ADG5

Отзывы:

Похожие инструкции для ADG5

Бренды по названию

Популярные бренды

KYMCO ADG5, Руководство пользователя

Результаты поиска

Содержание ADG5

Отзывы:

Похожие инструкции для ADG5

Бренды по названию

Популярные бренды