KYMCO ADG5 Скачать руководство пользователя страница 161

Страница: 161 / 426

3. Engine > Oil Pump

XCITING 400i

Oil Pump

SAFETY FIRST: Protective gloves and eyewear are recommended at this point.

GENERAL INSTRUCTIONS

The maintenance of lubrication system can be performed with the engine installed in

the frame. Use care when removing and installing the oil pump not to allow dust and

foreign matters to enter the engine and oil line.

Do not attempt to disassemble the oil pump. The oil pump must be replaced as a set

when it reaches its service limit.

After the oil pump is installed, check each part for oil leaks.

TROUBLESHOOTING

Oil level too low
1. Natural oil consumption

2. Oil leaks

3. Worn or poorly installed piston rings

4. Worn valve guide or seal

Poor lubrication pressure
1. Oil level too low

2. Clogged filter or oil passages

3. Not using the specified oil

3‐83

Содержание ADG5











































































































































































































































































































































































































































Результаты поиска

Содержание ADG5

Отзывы:

Похожие инструкции для ADG5

Бренды по названию

Популярные бренды

KYMCO ADG5, Руководство пользователя

Результаты поиска

Содержание ADG5

Отзывы:

Похожие инструкции для ADG5

Бренды по названию

Популярные бренды