KYMCO ADG5 Скачать руководство пользователя страница 24

Страница: 24 / 426

2.Periodic Maintenance XCITING S 400

Air Filter Servicing

Replace Air Filter as specified in Regular Maintenance Schedule. Check and

replace Air Filter Cartridge more frequently if vehicle is often used in dusty

environments or damp areas.

Replace Air Filter Cartridge

1. Remove outer casing of vehicle.

2. Remove Air Filter Cover.

3. Loosen Air Filter Cover Fixing Screw and take out the element.

Precautions on replacing Filter Element:

1. Make sure the Air Filter element is positioned correctly in the casing.

2. Do not start engine when Air Filter is not installed, or dirty air may enter the

engine and cause abnormal wear.

3. Do not wet the Air Filter element when cleaning the vehicle, or engine start may

become difficult.

4. Install Air Filter Cover and tighten Fixing Screw.

5. Re-install outer casing of vehicle.

9-4

Содержание ADG5











































































































































































































































































































































































































































Результаты поиска

Содержание ADG5

Отзывы:

Похожие инструкции для ADG5

Бренды по названию

Популярные бренды

KYMCO ADG5, Руководство пользователя

Результаты поиска

Содержание ADG5

Отзывы:

Похожие инструкции для ADG5

Бренды по названию

Популярные бренды