KYMCO ADG5 Скачать руководство пользователя страница 353

Страница: 353 / 426

10..Brake System

XCITING S 400

SAFETY FIRST: Protective gloves and eyewear are recommended at this
point.

Draining

The brake bleeding process is the same for the front and rear brakes.

Remove the two master cylinder cover screws with a #2 Phillips head screwdriver.

Remove the master cylinder cover, plastic piece and rubber accordion diaphragm.

Pour out any remaining brake fluid.

Clean and inspect the rubber diaphragm for tears or other damage. Replace as

necessary.

Pull off the rubber cap over the bleeder valve and crack open the bleeder valve

on the brake caliper using an 8 mm wrench. This valve is usually very tight so use

a box end wrench or a 6 point socket and ratchet to prevent rounding off the head.

Snug the bleeder valve back down.

Open the valve and remove the old brake fluid with a Mighty -Vac or a similar

device.

10-16

Содержание ADG5











































































































































































































































































































































































































































Результаты поиска

Содержание ADG5

Отзывы:

Похожие инструкции для ADG5

Бренды по названию

Популярные бренды

KYMCO ADG5, Руководство пользователя

Результаты поиска

Содержание ADG5

Отзывы:

Похожие инструкции для ADG5

Бренды по названию

Популярные бренды