KYMCO ADG5 Скачать руководство пользователя страница 51

Страница: 51 / 426

2.Periodic Maintenance XCITING S 400

Tires

Check grip between tire and ground and a normal tire pressure.

In case of a gripping anomaly, check tire pressure for normal reading using a

pressure gauge.

Pressure measurements of cool tire:

With 1 rider

Front Wheel 2.0 kgf/cm

Rear Wheel 2.25 kgf/cm

With 2 persons

Front Wheel 2.0 kgf/cm

Rear Wheel 2.25 kgf/cm

Measure pattern depth at center of tread pattern. Measurements shall be taken at

several points due to uneven wear.

Replace the tire if any of the measurements is lower than the service limit. Make

sure the wheel is properly balanced when a new tire is replaced.

Service Limits:

Front Wheel 1.6 mm
Rear Wheel 2.0 mm

Check Tread Pattern for Wear

Check tires before each riding. In case of finding a transverse line (minimum pattern

depth), nail or glass chip on the tire, or crack line on the side wall of tire, go to

Kymco dealer for replacing with new one. Excessive wear of tire tread pattern will

result in widened tread which is more prone to be punctured.

Tire Dimensions:

Front Tire Dimensions: 120/70-R15
Rear Tire Dimensions: 150/70-R14

9-31

Содержание ADG5











































































































































































































































































































































































































































Результаты поиска

Содержание ADG5

Отзывы:

Похожие инструкции для ADG5

Бренды по названию

Популярные бренды

KYMCO ADG5, Руководство пользователя

Результаты поиска

Содержание ADG5

Отзывы:

Похожие инструкции для ADG5

Бренды по названию

Популярные бренды