KYMCO ADG5 Скачать руководство пользователя страница 29

Страница: 29 / 426

2.Periodic Maintenance XCITING S 400

Brake Inspection

Brake Lever Adjuster

There is adjuster on each brake lever. Each adjuster has four positions so that the

released lever position can be adjusted to suit the rider’s hands.To adjust the

distance of the lever from the handlebar grip, push the lever forward and turn the

adjuster knob to align the number with the arrow mark on the lever holder.

Check and Adjust Brakes

1. Adjust brake lever clearance using adjustment knob (totally 4 adjustment

positions).

2. Push the brake lever forward when adjusting the knob (default setting is 2).

3. After adjustment, pull the Brake Lever (1) with hand until reaching a position

where fingers feel comfortable; check if the clearance at the front end of Brake

Lever is within the specified dimension.

9-9

Содержание ADG5











































































































































































































































































































































































































































Результаты поиска

Содержание ADG5

Отзывы:

Похожие инструкции для ADG5

Бренды по названию

Популярные бренды

KYMCO ADG5, Руководство пользователя

Результаты поиска

Содержание ADG5

Отзывы:

Похожие инструкции для ADG5

Бренды по названию

Популярные бренды