KYMCO ADG5 Скачать руководство пользователя страница 196

Страница: 196 / 426

5. Cooling System

XCITING S 400

Coolant

For the sake of safety, check level of cooling water before riding the vehicle.

Replace the cooling liquid as specified in Regular Maintenance Schedule.

Check Level of Cooling Water

1. Park the vehicle on level ground and brace it up with Main Stand.

2. Figure to be inserted

NOTICE

◆

Temperature in the engine may cause false reading of Cooling Water

level. Check water level after the engine cools down.

◆

Inclined vehicle may cause false reading of Cooling Water level.

3. Check level of Cooling Water via viewing window on the water preserving tank.

Make sure the level is between “F” and “L” marks.

NOTICE

◆

Before riding the vehicle, check the water tank and piping or any

leakage.

◆

Check the ground where the vehicle is parked for any leakage mark.

◆

Before riding the vehicle, check the fin and front protection screen of

water tank for any foreign object. Foreign objects may reduce the
cooling function or even cause vehicle or engine damage in worse
conditions.

5-3

Содержание ADG5











































































































































































































































































































































































































































Результаты поиска

Содержание ADG5

Отзывы:

Похожие инструкции для ADG5

Бренды по названию

Популярные бренды

KYMCO ADG5, Руководство пользователя

Результаты поиска

Содержание ADG5

Отзывы:

Похожие инструкции для ADG5

Бренды по названию

Популярные бренды