KYMCO ADG5 Скачать руководство пользователя страница 197

Страница: 197 / 426

5. Cooling System

XCITING S 400

Replenish Cooling Water (Fill the Reserve Water Tank)

1. Stand the vehicle upright on level ground.

2. Open Reserve Water Tank (remove screw 1 and cover 2), replenish water to

Upper Limit.

If level of cooling water gets excessively low, something must be wrong. Go to

a KYMCO Dealer for check and repair.

NOTICE

◆

Water temperature is very high after riding, do not open the cap of water

tank.

◆

Use soft water for mixing cooling liquid.

◆

Using poor quality cooling water may shorten the service life of water

tank. Please be careful.

◆

Replace cooling water in the tank every 10000km.

◆

Add proper amount of water tank additives to ensure performance of the

cooling system.

In case of fault of vehicle:

Go to a KYMCO dealer for check and repair if any fault occurs when riding the

vehicle. Use only original parts for replacement.

Check following items if engine does not start or engine stops when riding
the vehicle:

◆

Whether gasoline is sufficient.

◆

Whether Dashboard Fuel Indicator approaches E. Replenish with 95 unleaded

gasoline or better.

◆

Whether proper method is used for starting the engine.

◆

Others, whether any part is faulty.

5-4

Содержание ADG5











































































































































































































































































































































































































































Результаты поиска

Содержание ADG5

Отзывы:

Похожие инструкции для ADG5

Бренды по названию

Популярные бренды

KYMCO ADG5, Руководство пользователя

Результаты поиска

Содержание ADG5

Отзывы:

Похожие инструкции для ADG5

Бренды по названию

Популярные бренды