KW DAVID-613 Скачать руководство пользователя страница 6

Страница: 6 / 83

KW Aufzugstechnik GmbH Inbetriebnahme DAVID-613

DAVID-D613-Inbetriebnahme-V124-EE 18.02.2022 Seite - 6 -

Mounting of the Switching Cabinet – Example KW04M

The control cabinets KW01 and KW04 are intended for mounting on the wall.

If a switch cabinet socket is provided, the control cabinet is installed

with the Step 6.

Back to wall mounting: The control cabinets KW01 and KW04 have a guide groove

At the bottom of the bottom -> see picture Step 3. First, two screws are fixed in the wall,

whereupon the cabinet can be placed so that the top fixing holes can be marked and

drilled ...

Ensure that the fans are able to dissipate the heat to the right and left unhindered.

Assembly oft he Mounting Screws

As a first step, the two lower fixing holes are drilled into the masonry. First make sure that

the masonry has the necessary load bearing capacity. Otherwise, the use of a base is

recommended.

2 screws M8 with universal universal lever are used. The drilling distances are:

Distance of the drill holes in the cabinet KW04M: 490mm

Distance of drill holes in cabinet KW01N: 685mm

Positioning the Switching Cabinet in order to markt he As-

sembly-Holes above

Do not screw the screws completely into the wall so that the cabinet with its guide groove

can be placed on it and snapped into place.

Secure the cabinet with one hand against the drifting and mark the upper holes.

Now the cabinet can be safely placed on the floor again.

Making the Assembly-Drills above

Like the two lower ones, the two upper fixing holes are now drilled into the masonry.

To use are again 2 pieces of 10 universal blinds.

Final-Mounting - Mounting of the Switching Cabinet

Now the cabinet can be parked on its guide groove and click into place. The above

screws can be screwed in with a wrench or the ratchet.

Then the lower screws are tightened with a wrench.

If necessary (obstruction of the escape route) change the door stop.

For installations with a machine room, the cable duct is now installed.

Optional – Usage of a Socket of a Switch-

ing Cabinet

The KW06 and KW07 cabinets are supplied with a base as standard.

Optional sockets are available for cabinets KW03, KW04, KW240.

Before assembling the base, please make sure you know how to feed

the cables and make the corresponding cutouts!

The strain relief of the cables takes place in the base.

Содержание DAVID-613




















































































Результаты поиска

Содержание DAVID-613

Отзывы:

Бренды по названию

Популярные бренды

KW DAVID-613, Руководство пользователя

Результаты поиска

Содержание DAVID-613

Отзывы:

Бренды по названию

Популярные бренды