KW DAVID-613 Скачать руководство пользователя страница 46

Страница: 46 / 83

KW Aufzugstechnik GmbH Inbetriebnahme DAVID-613

DAVID-D613-Inbetriebnahme-V124-EE 18.02.2022 Seite - 46 -

Connection of the door drives via CANOpen

This is plugged into the lower CANbus terminal on the X11-XPU

module in the de-energised state.
Further door drives are extended with further CANbus cables on the

preceding line.
The last device is provided with a terminating resistor.

The connection of the door motor must only be carried out in a voltage-free state

! (Cir-

cuit diagram sheet 2 of 8).

The reversing contactor unit is located in an additional box

613. There is also space for the locking magnet control and an optional transformer.

Phase U Door-Engine Door 1

Phase V Door-Engine Door 1

Phase W Door-Engine Door 1

Phase U Door-Engine Door 2

Phase V Door-Engine Door 2

Phase W Door-Engine Door 2

Connection of the Photocell Door-1, Door-2 & Door-3

Attention! All inputs are + 24V DC inputs! Avoid the application of external voltage at

these terminals! The terminal for the connection of the light grating can be found on the

circuit board X11/.

+ 24V Voltage

200

+ 24V or 0V DC Input Photocell DOOR 1 / 2 / 3

42A/B/C

+ 24V DC Input Error Photocell DOOR 1 / 2 / 3

48A/B/C

0V GND

500

Set to PNP or NPN light curtains by means of the Jumper Right Top

Connection of the Audiovisual Alert H69

Attention! All inputs are + 24V DC inputs! Avoid the application of external voltage at

these terminals! The terminal for the connection of the light grating can be found on

the

circuit board X11 /.

The terminals are

169 and 500.

Connection of the Door-End-Switch, Revers-Con-

tact

Attention! All inputs are + 24V DC inputs! Avoid the application of external volt-

age at these terminals!

Attention! Inputs can be unlocked! Be sure to observe page 2 of 8 in the set!

Default setting:

Input Revers-Contact DOOR 1

FF1

Input Door-End-Switch-OPEN DOOR 1

FF2

Input Door-End-Switch-CLOSE DOOR 1

FF3

Input Revers-Contact DOOR 2

FF5

Input Door-End-Switch-OPEN DOOR 2

FF6

Input Door-End-Switch-CLOSE DOOR 2

FF7

Connection of the transom mate

The latching solenoid may only be connected in a de-energised state!

(Circuit diagram sheet 2 of). The connection is located in the additional box-613

Phase AC or + Voltage DC

715

N or 0V

716

Ground

Содержание DAVID-613




















































































Результаты поиска

Содержание DAVID-613

Отзывы:

Бренды по названию

Популярные бренды

KW DAVID-613, Руководство пользователя

Результаты поиска

Содержание DAVID-613

Отзывы:

Бренды по названию

Популярные бренды