KUHN EL162 Скачать руководство пользователя страница 120

Страница: 120 / 144

EL162

120

10. - Maintenance and storage

KN146AGB_L

Cultiplow

- Park the machine on an even fairly level ground.
- Remove guard (1).
- Place a container of sufficient capacity under drain

plug.

- Remove filler plug (2) and its washer.
- Remove drain plug (3) and its washer.
- Allow oil to drain completely.
- Wait for dripping to stop.
-

Clean and reinstall drain plug (3) and its

washer. Replace if necessary.

- Pour the correct oil quantity and quality through the

opening of the filler plug (2).

- Clean and reinstall filler plug (2) and its washer.

Replace if necessary.

- Reinstall guard (1):

• Torque setting for screws: 8.5 daNm (63 lbf ft).

Checking the oil level:

- Place the machine on level ground.
- Remove level plug (4):

• The oil level must reach lower part of level plug

hole (4).

- Top up if necessary.
- Clean and reinstall level plug (4) and its seal.

Replace if necessary.

Содержание EL162

















































































































































Результаты поиска

Содержание EL162

Отзывы:

Похожие инструкции для EL162

Бренды по названию

Популярные бренды

KUHN EL162, Руководство оператора

Результаты поиска

Содержание EL162

Отзывы:

Похожие инструкции для EL162

Бренды по названию

Популярные бренды