KUHN EL162 Скачать руководство пользователя страница 53

Страница: 53 / 144

6. - Putting into service

EL162

KN146AGB_L

Cultiplow

6.1.9 Uncoupling the machine

From the transport position:

- If the machine is fitted with skids, lower parking

stand to stabilize the machine.

- Lower the tractor three-point linkage to rest the

machine on the ground.

- Uncouple and place PTO shaft in support (1).
- Detach the top link from the machine end.
- Uncouple lower linkage arms.

The machine is uncoupled.

- When optional equipment is used, follow

specific procedures mentioned in the
related section:
• Optional equipment / Rear hydraulic lift

linkage / Coupling and uncoupling.

• Optional equipment / Rear attachment

with double acting hydraulic lift / Putting
the machine into transport position.

•

Optional equipment / Lights and
indicators / Coupling and uncoupling.

- Park the machine on an even fairly level

ground.

Содержание EL162

















































































































































Результаты поиска

Содержание EL162

Отзывы:

Похожие инструкции для EL162

Бренды по названию

Популярные бренды

KUHN EL162, Руководство оператора

Результаты поиска

Содержание EL162

Отзывы:

Похожие инструкции для EL162

Бренды по названию

Популярные бренды