KUHN EL162 Скачать руководство пользователя страница 99

Страница: 99 / 144

9. - Optional equipment

EL162

KN146AGB_L

Cultiplow

- Activate the single acting valve that controls the lift

cylinders of the hydraulic lift linkage.

- Attach safety chain (1) to cultirotor frame (2) and

hydraulic attachment frame (3) using shackles.

- Insert and lock pins using R-clips.
- Tighten chain.
- The transport position is obtained by raising the

tractor's three-point linkage.

The machine is in transport position.

- Never engage the tractor PTO drive when

the machine is in transport position.

9.11.4 Putting the machine into work position

From the transport position:

- Loosen chain (1).
- Unhook safety chain ((3) side).
- Activate the single acting valve that controls the lift

cylinders of the hydraulic lift linkage.

- Attach stroke limiters (1) to machine headstock (2).

- Check that there is no risk of the chain

getting caught during functioning.

Содержание EL162

















































































































































Результаты поиска

Содержание EL162

Отзывы:

Похожие инструкции для EL162

Бренды по названию

Популярные бренды

KUHN EL162, Руководство оператора

Результаты поиска

Содержание EL162

Отзывы:

Похожие инструкции для EL162

Бренды по названию

Популярные бренды