KUHN EL162 Скачать руководство пользователя страница 125

Страница: 125 / 144

10. - Maintenance and storage

EL162

125

KN146AGB_L

Cultiplow



"FAST-FIT" Cultitiller rotor:

Angled tines are available through KUHN PARTS:

• Left angled tines.
• Right angled tines.

Fitting instructions for angled tines:

- Lower the machine.
- Uncouple PTO shaft on machine side.
- Remove lynch pin (3).
- Check the condition of the lynch pin. replace it if

necessary.

- Remove worn tine and replace it with a new tine.
- Start fitting blades on the support nearest the side

gearbox.

- Fit first left blade (2) with the cutting edge facing

the left in the forward direction (left angled tine).

- Fit first angled tine (2) on support (1) using special

lynch pin (3).

- Fit second angled tine (4) with the cutting edge

facing the right in the forward direction (right
angled tine).

- Fit second angled tine (4) on support (1) using

special lynch pin (3).

- Repeat procedure on other tines.

- Position angled tine sharp edge in the rotor

direction of rotation.

Содержание EL162

















































































































































Результаты поиска

Содержание EL162

Отзывы:

Похожие инструкции для EL162

Бренды по названию

Популярные бренды

KUHN EL162, Руководство оператора

Результаты поиска

Содержание EL162

Отзывы:

Похожие инструкции для EL162

Бренды по названию

Популярные бренды