KUHN EL162 Скачать руководство пользователя страница 107

Страница: 107 / 144

9. - Optional equipment

EL162

107

KN146AGB_L

Cultiplow

9.12.3 Removal

- When parking the machine and additional

machine, the additional machine must be
lowered first.

- Disconnect and place hydraulic hose couplers in

their holders.

9.12.4 Putting the machine into transport

position

- If the machine is used with an additional

driven machine, uncouple pto shaft
between machine and additional machine
before fully raising the additional machine.

From the working position:

- Uncouple the PTO shaft (between machine and

additional machine).

- Activate the transport/work cylinder control valve

in the "pivot into transport" position.

- Remove pin (2).
- Fit safety plate (1).
- Insert and secure lynch pin (2).
- The transport position is obtained by raising the

tractor's three-point linkage.

The machine is in transport position.

- Never engage the tractor PTO drive when

the machine is in transport position.

REPOSER LE SEMOIR AU SOL

LOWER SEEDER TO THE GROUND

SÄMASCHINE IMMER ABSENKEN

APPOGGIARE LA SEMINATRICE
AL SUOLO

DEJAR LA SEMBRADORA EN
EL SUELO

- AVANT L’ARRET DU MOTEUR
- AVANT TOUTE INTERVENTION
- AVANT LA DEPOSE DE L’ENSEMBLE

- BEFORE STOPPING TRACTOR ENGINE
- BEFORE ANY MAINTENANCE
- BEFORE REMOVING FROM TRACTOR

- VOR ABSTELLEN DES MOTORS
- VOR JEDER ARBEIT AM GERÄT
- VOR ABBAU DER MASCHINE

- PRIMA DI ARRESTARE IL MOTORE
- PRIMA DI QUALSIASI IMTERVENTO
- PRIMA DI DISTACCARE L’INSIEME

- ANTES DE LA PARADA DEL MOTOR
- ANTES DE TODA INTERVENCION
- ANTES DE LA DESCARGA DEL CONJUTO

Содержание EL162

















































































































































Результаты поиска

Содержание EL162

Отзывы:

Похожие инструкции для EL162

Бренды по названию

Популярные бренды

KUHN EL162, Руководство оператора

Результаты поиска

Содержание EL162

Отзывы:

Похожие инструкции для EL162

Бренды по названию

Популярные бренды