KUHN BELT-DRIVEN MINOTOR 3060 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 64

background image

27

BELT-DRIVEN MINOTOR 3060

C

A

E

B

D

ENGAGING AND DISENGAGING THE BEATER BAR

Lever A

Pull lever down to engage the beater bar.
Push lever up to disengage the beater bar.

RAISING / LOWERING THE MACHINE BODY

Lever A

The movements are made by pressing the switch on the control handle.
Turn lever to the left to lower the body.
Turn lever to the right to raise the body.

RAISING / LOWERING THE DELIVERY CHUTE

Lever A

Turn lever to the left to point the chute upwards.
Turn lever to the right to point the chute downwards.

«
...
25
26
27
28
29
...
»

Содержание BELT-DRIVEN MINOTOR 3060

































































Отзывы:

Нет отзывов

Похожие инструкции для BELT-DRIVEN MINOTOR 3060

Бренд: NEILPRYDE Страницы: 53

Бренд: JAC Страницы: 103

Бренд: 3Disc Страницы: 12

Бренд: Rainbow Страницы: 18

Бренд: xsto Страницы: 76

Бренд: F&V Страницы: 5

Бренд: F Care Systems Страницы: 2

Бренд: Ofa Bamberg Страницы: 80

Бренд: Vahle Страницы: 36

Бренд: Vahle Страницы: 20

Бренд: Vacon Страницы: 102

Бренд: Velp Scientifica Страницы: 16

Бренд: Velp Scientifica Страницы: 2

Бренд: Velp Scientifica Страницы: 32

Бренд: Velleman-Kit Страницы: 32

Бренд: Yetter Страницы: 24

Бренд: Yetter Страницы: 32

Бренд: GE Страницы: 176

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды