Kubota VS 220 Скачать руководство пользователя

Страница: 66 / 154

Before first use

Put the machine on a supporting beam before moving in between
the tractor and machine

This will ensure that the machine cannot drop if the power lift should

inadvertently be operated while you are between the tractor and

machine. Switch the tractor motor off. Without the support, a power lift

that drops could wedge you in, resulting in possible serious physical

injury.

Extreme working angle coupling shaft

The maximum operating angle of the coupling shaft is 30

when lifted

and 30

when lowered.This is the maximum length between the PTO

shaft and the machine drive axle.



Place the machine on a supporting beam wit the power lift in the

highest position.



Switch the tractor off and remove the keys from the ignition.



Engage the parking brake of the tractor.



Check if the furthest working angle is less than 30



Check that the overlap of the profiled tubes is still at least 6”.



Remove the tractor section.



Apply grease to the profiled tubes.



Attach the protection sleeves.



Slide the coupling shaft halves into each other.



Mount the coupling shaft to the machine.

Always mount the check chains of the protection sleeves

The check chains prevent the protection sleeves from rotating with the

coupling shaft. Crop or pieces of clothing can be wound around

rotating protection sleeves and cause material damage and possibly

severe physical injury.



Fit the check chains to both ends of the coupling shaft protection

sleeves.



Mount the other ends of the chains to a fixed point of the tractor,

respectively the machine.

max.30

Содержание VS 220



























































































































































Результаты поиска

Содержание VS 220

Отзывы:

Похожие инструкции для VS 220

Бренды по названию

Популярные бренды

Kubota VS 220, Руководство пользователя

Результаты поиска

Содержание VS 220

Отзывы:

Похожие инструкции для VS 220

Бренды по названию

Популярные бренды