Kubota VS 220 Скачать руководство пользователя

Страница: 102 / 154

To be done before spreading

102

Review and adaptation

The maximum acceptable loss in the ditch is determined by

environment standards (EN 13739-1). In order to comply with the

standards the quantity of fertiliser in the 1st trough, standing in the

imaginative ditch, must be a maximum of 10% of the quantity collected

in the trough in the middle of the track (= 100%).

The trough on the land next to the fictive ditch provides an insight into

the topping. It will never be 100%.

Good spreading pattern, the border spreading has been

adjusted well.

You are spreading too narrowly:



Reduce the driving distance to the ditch (border-

spreading plate)



Increase the PTO shaft rpm (standard spreader)



Or reduce the inclination of the border-spreading

cylinder



Repeat the test

You are spreading too wide:



Increase the driving distance to the ditch (border-

spreading plate)



Reduce the PTO shaft rpm (standard spreader)



Or increase the inclination of the border-spreading

cylinder. If this is already maximum: increase the PTO

shaft rpm



Repeat the test

Ditch side

Содержание VS 220



























































































































































Результаты поиска

Содержание VS 220

Отзывы:

Похожие инструкции для VS 220

Бренды по названию

Популярные бренды

Kubota VS 220, Руководство пользователя

Результаты поиска

Содержание VS 220

Отзывы:

Похожие инструкции для VS 220

Бренды по названию

Популярные бренды