Kubota VS 220 Скачать руководство пользователя страница 47

Страница: 47 / 154

Assembly instruction

* Fit the VS-VITI top frame longitudinally.



Mount the frame supports to the top frame.

The forks of the frame supports must face the front.



Fasten the top frame to the lower frame with the provided spacers,

bolts and nuts.



Mount simultaneously the coupling shaft support to the fastening

point on the front of the machine.



Mount the linkage pins, the top pin and their lock clips.

VS 400-500 VITI

The procedure is the same as the above-described assembly

instruction for the VS400-500. Only the top frame is mounted

lengthwise.

Place spreading unit



Mount the spreading unit to the frame



See paragraph »Assembly of the spreading unit in the frame«

on page 41.

Connect operation with the regulating rod



Secure the regulating rod to the lower hole of the hinge pin.



Assemble, if delivered, the hydraulic operation.

Top frame

Lock clip

Lower frame

Frame supports

Coupling shaft

support

Linkage pin with lock clip

Top pin

Forks facing forward

Содержание VS 220



























































































































































Результаты поиска

Содержание VS 220

Отзывы:

Бренды по названию

Популярные бренды

Kubota VS 220, Руководство пользователя

Результаты поиска

Содержание VS 220

Отзывы:

Бренды по названию

Популярные бренды