Kubota VS 220 Скачать руководство пользователя страница 99

Страница: 99 / 154

To be done before spreading



Only stop spreading after you have driven at least half a working

width over the troughs.



Drive back in the next track, in the middle over trough 7. Maintain

the same distance with opening and closing the dosing. Keep to

the same driving speed and PTO shaft rpm!

If you have set a small application rate, drive to and fro over the same

track in order to collect sufficient fertiliser in the troughs for a good

comparison. Maintain the same distance with opening and closing the

dosing. Keep to the same driving speed and PTO shaft rpm!

Review and adaptation

The content of the separate tubes can differ 15% at most from the

average:

Good spreading pattern, the spreader has been adjusted

well.

The spreader is not spreading wide enough.



Adjust the rpm or the turn of the spreading spout.



Repeat the test.

The spreader is spreading too wide.



Adjust the rpm or the turn of the spreading spout.



Repeat the test.

Содержание VS 220



























































































































































Результаты поиска

Содержание VS 220

Отзывы:

Бренды по названию

Популярные бренды

Kubota VS 220, Руководство пользователя

Результаты поиска

Содержание VS 220

Отзывы:

Бренды по названию

Популярные бренды