manualshive.com logo in svg

Kubota VS 220, Руководство пользователя

Поделиться
Скачать
Kubota VS 220 Скачать руководство пользователя страница 65

Before first use

65

Setting the safety clutch

There is a safety clutch on the machine side of the coupling shaft. This 

safety clutch protects the machine against overloading.

First check the setting of the pressure springs in the safety clutch.

The spring length must be 1 1/16”.

A static calibration test can be performed with a torque wrench.

Set the torque wrench to 220 ft.lbs.

Friction should occur as soon as it is turned.

T

IP

It  is  possible  that  the  coupling  should  be  “broken  out”  at  a  higher 

torque for the first time.

Attach the loose machine component of the coupling shaft to the 

drive axle.

At the side of the machine the coupling shaft is secured with a 
bolt.

Shift the coupling shaft onto the drive axle of the machine.

Take care that the large hole in the coupling shaft hub is above the 

chamber in the hole of the drive axle.

Push the bolt through the coupling shaft and drive axle.

Don’t  tighten  the  nut  yet,  you  still  have  to  adjust  the  length  of  the 

coupling shaft and put back the protection sleeves.

See paragraph »Checking the coupling shaft length« on page 64.

Manually align the two coupling shaft halves.

Check the length and set it as described in paragraph »Shortening 

the coupling shaft« on page 65.

After shortening and assembling the coupling shaft, tighten the nut 

at 52 ft.lbs.

Shortening the coupling 

shaft

The profiled tubes must overlap as far as possible, with a 6” minimum.

At  the  outer  edges,  the  profiled  tubes  must  have  at  least  1”  free 

clearance, when the tractor PTO shaft and the machine drive axle are 

level.

Cut off the two profiled tubes to achieve the 1” clearance.

Deburr both ends.

Clean the coupling shaft.

Shorten the protection sleeves by the same length.

Slide the coupling shaft halves into each other.

Connect the coupling shaft of the machine and the tractor.

Lift the machine with the power lift in the highest operating position.

Securing bolt

Coupling shaft

Drive axle

Chamber in 

the drive axle

Содержание VS 220



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды