Kubota VS 220 Скачать руководство пользователя страница 114

Страница: 114 / 154

Use on the land

114

Working method

Placing the border-spreading plate in working position,



Switch the tractor off and remove the keys from the ignition.



Engage the parking brake of the tractor.



Fit the border-spreading plate in working position.



Remove the 2 lock clips that hold the plate in transport position.



Pull the plate forward from its transport position.



Turn the plate to its working position and insert the 2 tubes in

the holder pipes.



Secure the plate with the clip through the top pipe on the holder.



Push the other clip back in the transport hook on the hopper.



Check if the position of the border-spreading plate is correct:
Seen in the drive direction the spreading plate stands at an angle
of 20

inward.

Adjusting spreader setting

The spreader is already set at full-field spreading according to

the values in the left column of the chart:

The right-hand column shows the adjustments during border

spreading

OTE

: If you reduce the original application rate to 30 – 50% you can go

below the 45 lbs/min. flowrate.



Then go over to fine application.

Holder pipes

Lock clips

Remove 2 lock clips

Transport hook

Transport position

Work position

Spreading data

Full-field spreading

Border spreading plate

Working width (ft)

drive 10 feet from the

border

Driving speed (mph)

5 (higher gear)

Application rate (lbs/acre)

175

30 or 50% = 58 or 87

Flowrate (lbs/min.)

23* or 34*

Adjusting nut position (PK 15.30)

Fine application! 34* or 42*

PTO shaft RPM

540

370

Fine application*

Yes (< 45 lbs/min.)

With fine application you use the adjusting nut position of a 3x higher flowrate!

Through lower PTO shaft rpm you must shift one or more gears higher

Содержание VS 220



























































































































































Результаты поиска

Содержание VS 220

Отзывы:

Бренды по названию

Популярные бренды

Kubota VS 220, Руководство пользователя

Результаты поиска

Содержание VS 220

Отзывы:

Бренды по названию

Популярные бренды