Kubota VS 220 Скачать руководство пользователя

Страница: 48 / 154

Assembly instruction

VS400 hopper assembly



Lubricate the rubber fasteners with Vaseline or grease and place

them from the inside into the hopper holes.



Fit the hopper supports on the outside of the hopper.



Push the bolts from inside through the hopper.



Fit, if provided, the steel hopper lining.

Steel hopper lining assembly

(accessory)

To prevent excessive wear and tear of the hopper a steel lining
protects the hopper at the height of the optional stirring device.



Put the lining in the hopper and mark the drilling holes.



Drill the marked holes with an 7/16” drill.



Fasten the lining with the carriage bolts from the inside and the

washers and nuts on the outside.

Fork

Fastener

Hopper supports

11/32”

Bolt head on the inside

7/16”

Содержание VS 220



























































































































































Результаты поиска

Содержание VS 220

Отзывы:

Похожие инструкции для VS 220

Бренды по названию

Популярные бренды

Kubota VS 220, Руководство пользователя

Результаты поиска

Содержание VS 220

Отзывы:

Похожие инструкции для VS 220

Бренды по названию

Популярные бренды