Kubota VS 220 Скачать руководство пользователя страница 92

Страница: 92 / 154

To be done before spreading

Loading height

You can fill the spreader to the desired levels after it has been put in

place. If no activities need to be performed on top of the hopper, the

height can be adjusted with the automatic filling system.

A load platform must be used if the distance between the hopper rim

and the ground is more than 4 feet while filling manually or with large

bags. The filling height is given in



paragraph »Technical specifications« on page 34.

Working method



If a fixed loading platform is used, drive the machine to the

platform. The distance between the machine and the platform must

be a maximum of 8”.



Lower the machine at the desired level.



Ensure that the dosing unit is closed and close it, if necessary.



Switch the tractor off and remove the keys from the ignition.



Engage the parking brake of the tractor.



Close all the doors and windows in the cabin.



Place wheel chocks in front of the wheels of the tractor.



If a mobile loading platform is being used, place the loading

platform at the spreader so that there would be a maximum

distance of 8” between the two.



Open the hopper cover.



Fill the machine to the desired level with the correct tools.

NDICATION

Work carefully while filling and take the regulations that apply to

working conditions into consideration! Make sure no objects or tools

fall into the hopper as it could block or damage the spreader!



Close the hopper cover.

Do not exceed the maximum recommended weight!



See also paragraph »Technical specifications« on page 34.

The machine has not been constructed to carry the additional
weight.

Keep in mind the permitted axle load, load capacity of the tyres and

the total weight of the tractor and machine, as well as the minimum

axle load of the tractor.



machines« on page 16.

If the weight should increase the filled spreader could fall backwards!



Set the spreader level length wise after it has been filled.

Содержание VS 220



























































































































































Результаты поиска

Содержание VS 220

Отзывы:

Бренды по названию

Популярные бренды

Kubota VS 220, Руководство пользователя

Результаты поиска

Содержание VS 220

Отзывы:

Бренды по названию

Популярные бренды