Kubota VS 220 Скачать руководство пользователя страница 44

Страница: 44 / 154

Assembly instruction



Bring the two cables with the lamp around the hopper to the

assembly points on the support.



Take care that moving control parts do not touch the cable.

That way damage by moving parts is prevented.



Mount the lamps with the protective cap on the supports with two

washers and M5 nuts each.



Use the provided cable ties to conceal and tie up the cables well.

The two large ties are used to fasten the joined cable with plug.



Mount the free socket on the hopper

Socket for lighting plug

If the machine is equipped with lighting the free socket is mounted on

the hopper. Placed in this spot the plug stays clean and undamaged

during the storage of the machine.



Mark the 3 holes on the hopper.



Select the place in such a way that during disconnecting and

storing the cable the socket is easily accessible.



Drill holes 7/32”.



Fit the socket.

Spreading spout assembly

The spreading spout has a quick lock through which the spout can

quickly be fitted or removed.



See paragraph »Spreading spout assembly« on page 60.

Attach hopper cover

The hopper cover must be pulled over the coaming or hopper

extension to protect the contents against rain or splashing water.



Take care that the elastic edge fits loosely around the coaming.
Only then will the hopper cover stay in place!

Cable with plug

Protective cover

Lamp

Socket

Lighting plug

Hopper cover for coaming

Содержание VS 220



























































































































































Результаты поиска

Содержание VS 220

Отзывы:

Бренды по названию

Популярные бренды

Kubota VS 220, Руководство пользователя

Результаты поиска

Содержание VS 220

Отзывы:

Бренды по названию

Популярные бренды