Kubota VS 220 Скачать руководство пользователя

Страница: 40 / 154

Assembly instruction

VS220 frame assembly



Assemble the support for the coupling shaft.



Mount the cord with the lock clip.



Put the top pin in the top connection.



Secure the top pin with the lock clip.



Place the lock clips on the linkage pins.

Assembly of VS220 control parts

The supplied control parts should be fitted to the basic frame

depending on the model.

Manual operation



Fit the two arms with the hinge bushings to the frame



Bring the arms together with the lever in between and connect

these with the two bolts and nuts.

Hydraulic operation

The lever for the manual operation is not used with the hydraulic

operation. In its place is a strip as filler between the two arms.



See »Hydraulic operation« on page 54 for further assembly

instructions of the hydraulic operation.

Lock clip

Top pin

Linkage pins

Lock clip

Coupling shaft

support

Coupling shaft support attachment

point

Connecting points for regulating rod and cylinder

Lever for manual operation

Hydraulic operation

Содержание VS 220



























































































































































Результаты поиска

Содержание VS 220

Отзывы:

Похожие инструкции для VS 220

Бренды по названию

Популярные бренды

Kubota VS 220, Руководство пользователя

Результаты поиска

Содержание VS 220

Отзывы:

Похожие инструкции для VS 220

Бренды по названию

Популярные бренды