Kubota VS 220 Скачать руководство пользователя

Страница: 54 / 154

Assembly instruction

Hydraulic operation

In the case of hydraulic operation the dosing mechanism can be

operated with a single-acting hydraulic valve from the tractor.



Fasten the hinge pin to the frame with a washer and clamping pin.



Attach the fastening plate to the spreader unit. Use the outermost

hole in the plate. Tighten the nut manually.



Drill the blinded hole in the cap of the spreader unit with an 7/16”

drill.



Lay the spacer ring on the drilled hole.



Push a nut from the underside through the hole, the washer and

the plate.



Fasten the plate by tightening the nuts with the correct tension.



Secure the regulating rod to the lower hole of the hinge pin.



Mount the hydraulic cylinder to the fastening plate. The

accumulator must face outwards.



Fit the cylinder fork to the middle hole of the hinge pin.



Fasten the hose to the cylinder.



Attach the hydraulic hose to a hydraulic valve of the tractor and to

the valve.



Check the hydraulic components for leakage and damage.



See paragraph »Checking the hydraulic system« on page 132.

Accumulator

Fixing plate

Hinge pin

Regulating rod

Ø 7/16”

Outermost hole

Fork

Tap closed

Содержание VS 220



























































































































































Результаты поиска

Содержание VS 220

Отзывы:

Похожие инструкции для VS 220

Бренды по названию

Популярные бренды

Kubota VS 220, Руководство пользователя

Результаты поиска

Содержание VS 220

Отзывы:

Похожие инструкции для VS 220

Бренды по названию

Популярные бренды