Kubota VS 220 Скачать руководство пользователя страница 89

Страница: 89 / 154

To be done before spreading

Other settings

If during the reduction of the working width the PTO shaft rpm

becomes too low it is optional to adjust the spreading spout angle.

Spreading spout angle

adjustment (accessory)

Working widths vary with the angle of the spreading spout

This enables you to reduce the working width by approx. 25%.

The standard spreading spout spreads with the small angle of approx.

30 feet working width instead of 40 feet with the large angle.

Adjusting the spreading spout angle with the key

The reciprocating movement of the spreading spout can be set to a

smaller angle with an optional key. The angle adjustment can be

reached through a covered opening in the protective cover of the

spreading unit.



Remove the cap in the protective cover.

Spreading spout angle adjustment in maximum position. The arrow

points to Max.



Put the key with the arrow upwards in the adjustment.



Press the key, against the spring pressure, into the adjustment.

Angle min. 48

Angle max. 56

Cap

Arrow on adjusting piece

Adjustment of the spreading spout angle

Key with arrow upwards

Содержание VS 220



























































































































































Результаты поиска

Содержание VS 220

Отзывы:

Бренды по названию

Популярные бренды

Kubota VS 220, Руководство пользователя

Результаты поиска

Содержание VS 220

Отзывы:

Бренды по названию

Популярные бренды