Kubota VS 220 Скачать руководство пользователя страница 123

Страница: 123 / 154

Storing the machine

123

If you cannot lower the power lift far enough to release the catch

hooks, we advise you to place the spreader on a firm, stable ramp, for

example a pawl.

For the VS600 model, it is easy to disconnect and put away the empty

spreader with a set of parking wheels.



Drive the tractor about 3/4 foot forward (maximum distance

depends on the range of the coupling shaft; the halves must

always overlap each other).



Switch the tractor off, remove the key from the ignition and engage

the parking brake of the tractor.



Disconnect the electric plugs and hang them in the container.



Disconnect the hydraulic hoses.



Place the protective caps on the hydraulic hose connections.



Hang the hydraulic hoses in the hose coupling support.



Disconnect the coupling shaft and hook it up.

Preparation for winter

storage

At the end of the season the machine must be prepared for winter

storage.

If the machine is being put away for a short or longer period of time it

is recommended that you lubricate and clean it first. If it is lubricated

first you will prevent dirt, fertiliser and water from entering the

bearings.

The advantages of this method of working are:

•

additional checks on the machine right after work,

•

Ensuring the longevity of the machine,

•

less delays due to problems while working with the machine.

When using a high-pressure cleaner, do not aim it at the seals. That

way you will prevent dirt and moisture from entering.



Clean the machine.



Let the machine dry.



Paint any damaged paintwork.



Lubricate and oil all points once again to ensure conservation.



See paragraph »Maintenance intervals« on page 126.



Coat blank parts such as piston rods of hydraulic cylinders with

preserving grease.

Only use grease that would not harden or dry. That will prevent

damage to cylinder oil seals.



Store the ED II control box in a place where it cannot be damaged

and is not exposed to temperatures below -20

Parking wheels

Содержание VS 220



























































































































































Результаты поиска

Содержание VS 220

Отзывы:

Бренды по названию

Популярные бренды

Kubota VS 220, Руководство пользователя

Результаты поиска

Содержание VS 220

Отзывы:

Бренды по названию

Популярные бренды