manualshive.com logo in svg

Kubota VS 220, Руководство пользователя

Поделиться
Скачать
Kubota VS 220 Скачать руководство пользователя страница 64

Before first use

64

Mounting the 

coupling shaft

The coupling shaft provided is too long for most types of tractors

The coupling shaft must be made the correct length before connecting 

it to the tractor. A coupling shaft that is too long could lead to serious 

damage to the machine and the tractor.

See the paragraph »Checking the coupling shaft length«, and

the paragraph »Shortening the coupling shaft«.

During lifting and lowering of the power lift, the coupling shaft requires 

adequate space for

•

sliding in and out,

•

sufficient overlap between the profiled tubes when driving the 

machine in the extreme operating angle of the coupling shaft.

Connect the machine to the tractor but keep the coupling shaft 

loose!

See chapter »Hitching to the tractor« on page 67.

Checking the 

coupling shaft length

Put the machine on a supporting beam before moving in between 
the tractor and machine

This will ensure that the machine cannot drop if the power lift should 

inadvertently  be  operated  while  you  are  between  the  tractor  and 

machine. Without the support, a power lift that drops could wedge you 

in, resulting in possible serious physical injury.

NOTE!

The length of the coupling shaft and the shortening thereof must be 

done after the power lift has been connected, but before the coupling 

shaft has been connected.

Lift the machine with the power lift until the PTO shaft and the 

machine drive axle are level.

This is the shortest possible length between the two shafts.

Place the machine on a supporting beam.

Switch the tractor engine off and remove the keys from the ignition.

Engage the parking brake of the tractor.

Disconnect the coupling shaft for it to be two halves.

Remove the protection sleeves

Mount the loose tractor section of the coupling shaft to the tractor 

PTO shaft.

Axles on the same height

Safety plate

Содержание VS 220



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды