KSB PumpDrive Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 162

background image

8 Maintenance/inspection

8.1 Safety regulations

The operator ensures that all maintenance, inspection and installation work is
performed by authorised, qualified specialist personnel who are thoroughly familiar
with the manual.

DANGER

Unintentional start-up
Danger of death from electric shock!

▷

Disconnect the PumpDrive from the power supply before performing any
maintenance or installation work.

▷

Ensure that the PumpDrive cannot be switched on again during maintenance
and installation work.

DANGER

Contact with live components
Risk of fatal injury due to electric shock!

▷

Never remove the upper housing part from the heat sink.

▷

Mind the capacitor discharge time.
After switching off PumpDrive, wait five minutes until dangerous voltages have
discharged.

NOTE

All maintenance, service and installation work can be carried out by KSB Service or
authorised workshops. Find your contact in the attached "Addresses" booklet or on
the Internet at "

www.ksb.com/contact

".

8.2 Maintenance/inspection

8.2.1

Supervision of operation

PumpDrive must run quietly and free from vibrations at all times.
Ensure sufficient cooling for PumpDrive.
In dirty environments, clean the air vents and housing surface regularly.

8.3 Dismantling

8.3.1

Preparing PumpDrive for dismantling

1.

Interrupt the power supply to the pump system.

2.

Disconnect PumpDrive.

3.

Decouple PumpDrive.

8 Maintenance/inspection

98 of 162

PumpDrive

«
...
96
97
98
99
100
...
»

Содержание PumpDrive



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PumpDrive

Бренд: Camozzi Страницы: 12

Бренд: elero Страницы: 10

Бренд: I/O Magic Страницы: 32

Бренд: Lenze Страницы: 8

Бренд: lumishore Страницы: 7

Бренд: D+H Страницы: 8

Бренд: Danfoss Страницы: 8

Бренд: Tridonic Страницы: 12

DUW160812X0502A

Бренд: AOpen Страницы: 41

Бренд: Franklin Electric Страницы: 28

Бренд: Pacific Scientific Страницы: 107

Бренд: Mannesmann Страницы: 128

3242 BX4 Series

Бренд: Faulhaber Страницы: 52

Бренд: Fagor Страницы: 420

USB 2.0 CD-RW/DVD-ROM Combo Drive

Бренд: IBM Страницы: 74

Бренд: Parker Automation Страницы: 362

AlphaStep AZ Series

Бренд: Oriental motor Страницы: 120

AF-650 GP Series

Бренд: GE Страницы: 175

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды