KSB PumpDrive Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 162

background image

5 Installation at Site

5.1 Safety regulations

DANGER

Incorrect installation

Danger to life!

▷

Install PumpDrive in a flood-proof location.

▷

Never use PumpDrive in potentially explosive atmospheres.

5.2 Checks to be carried out prior to installation

Place of installation
The standard configuration has IP 55 enclosure protection and may only be used in
environments for which its enclosure provides adequate protection.
The place of installation must meet the following requirements:

▪

Well ventilated

▪

No direct sunlight

▪

No oil-laden air

▪

Protected from weather

▪

Sufficient clearance for ventilation and dismantling

▪

Flood-proof

Provide PumpDrive with suitable protection when installed outdoors to prevent
condensation on the electronic equipment and exposure to excessive sunlight.

Ambient conditions
The ambient conditions specified in the following table must be observed:
Table 12: Ambient conditions

Operating temperature

Temperature

[°C]

Without power derating

0 °C to +40 °C

With power derating

0 °C to +50 °C

The service life of PumpDrive is reduced if an average temperature of +35 °C/24 h is
exceeded or if PumpDrive is operated at temperatures below 0 °C or above +40 °C. In
addition, the power rating is reduced.
PumpDrive switches off automatically if excessively high or low temperatures occur.

NOTE

Contact the manufacturer if the device is to be used under ambient conditions
other than those described above.

5.3 Mounting PumpDrive

Depending on the selected mounting option, an adapter or installation kit is
required.

5.3.1

Motor mounting

The motor-mounted PumpDrive model is supplied, together with the pump, already
mounted to the motor via an adapter.
Adapters for subsequent conversion to the motor mounting configuration for
existing pump systems are available from KSB.

Outdoor installation

5 Installation at Site

PumpDrive

19 of 162

«
...
17
18
19
20
21
...
»

Содержание PumpDrive



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PumpDrive

Bell & Gossett ecocirc XL Series

Бренд: Xylem Страницы: 25

Бренд: I/O Magic Страницы: 32

Бренд: Lenze Страницы: 8

Бренд: TDE MACNO Страницы: 66

Super-writemaster SH-S203N

Бренд: Samsung Страницы: 2

Super-writemaster SH-S203D

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 10

Бренд: Samsung Страницы: 15

SE-S084C - DVD±RW / DVD-RAM Drive

Бренд: Samsung Страницы: 1

Бренд: Samsung Страницы: 16

Бренд: Samsung Страницы: 25

writemaster SE-S164L

Бренд: Samsung Страницы: 28

Бренд: Samsung Страницы: 21

Бренд: Samsung Страницы: 25

Бренд: Samsung Страницы: 20

Бренд: Samsung Страницы: 33

SH-M522C - CD-RW / DVD-ROM Combo Drive

Бренд: Samsung Страницы: 27

Бренд: Samsung Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды