KSB PumpDrive Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 162

background image

11 Trouble-shooting

DANGER

Unintentional start-up
Danger of death from electric shock!

▷

Disconnect the PumpDrive from the power supply before performing any
maintenance or installation work.

▷

Ensure that the PumpDrive cannot be switched on again during maintenance
and installation work.

NOTE

Depending on the combination of settings, PumpDrive could conceivably restart

automatically after acknowledgement/reset or when the cause of the malfunction

or fault has been eliminated.

Reset PumpDrive to factory settings prior to implementing all fault rectification
measures (

Section 7.3.1 Page 93) .

11.1 Faults/Malfunctions: Trouble-shooting

WARNING

Improper work to remedy faults at the pump (set)
Risk of injury!

▷

For any work to remedy faults at the pump (set) observe the relevant
information in this manual or in the relevant accessory manufacturer's
documentation.

If problems occur that are not described in the following table, consultation with
KSB’s customer service is required.
Mains fuse rating too small for the nominal mains current.
PumpDrive does not start
PumpDrive runs unevenly
Max. speed not reached.
PumpDrive running at maximum speed only
PumpDrive running at minimum speed only
No 24 V supply.
Wrong direction of rotation of the motor.
Fault message/protective tripping.

Table 111: Faults

A B C D E F G H I Possible causes

Remedy

✘

✘

No voltage

Check the mains voltage; check the mains fuses

✘

No enable

Insert jumper/enable via field bus

✘ ✘

Mains cables connected
incorrectly/
Fault in supply line

Check wiring

✘

Mains fuse rating too small for
PumpDrive input current

Section 5.4.2.1 Page 21)

✘ ✘

No setpoint signal (internal/
external)

Check the setpoint signal (internal/external)

✘ ✘

✘

Permissible voltage range
undershot/exceeded

Check the mains voltage; supply PumpDrive with the
specified voltage (via transformer, if necessary)

✘

Wrong direction of rotation
set

Change the direction of rotation.

✘ ✘ ✘

✘

✘

PumpDrive overload

Reduce the power input by lowering the speed;
check the motor/pump for blockages.

A

B
C

D

E

F

G
H

I

11 Trouble-shooting

PumpDrive

131 of 162

«
...
129
130
131
132
133
...
»

Содержание PumpDrive



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PumpDrive

AF-650 GP Series

Бренд: GE Страницы: 212

Бренд: Yale Страницы: 14

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

TOPDRIVE20 Series

Бренд: TECHTOP Страницы: 2

Бренд: Leadshine Страницы: 22

SubDrive Connect Plus SDCP-CEN0723

Бренд: Franklin Electric Страницы: 12

LonWorks MCH Series

Бренд: Lenze AC Tech Страницы: 27

Бренд: STG-BEIKIRCH Страницы: 27

Бренд: Eaton Страницы: 204

Allen-Bradley PowerFlex 753

Бренд: Rockwell Automation Страницы: 20

DuroSpeed Series

Бренд: Borg Warner Страницы: 15

Бренд: GSK Страницы: 79

Бренд: GSK Страницы: 105

Бренд: Metronix Страницы: 171

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды