KSB PumpDrive Скачать руководство пользователя страница 42

Страница: 42 / 162

6.2.3

Navigation keys

The navigation keys are used for navigating in the menus and for confirming
settings.
Table 33: Assignment of navigation keys

Key

Function

Arrow keys:

▪

Move up/down in the menu options.

▪

Increase/decrease a numerical value.

Esc

Escape key:

▪

Delete/reset entry

(the entry is not saved).

▪

Move up one menu level.

OK key:

▪

Confirm settings.

▪

Confirm menu selection.

▪

Move to the next digit when entering numerals.

▪

Alert reset

Help key:

▪

Displays a help text for each selected menu option.

6.2.4

Operating keys

Table 34: Assignment of operating keys

Key

Description

Man

Starts PumpDrive in manual operating mode

Off

Stops PumpDrive

Auto

Switches to automatic mode

Func

Parameterisable function key

Manual mode via control panel

NOTE

After a power failure, PumpDrive reverts to OFF mode and manual mode must be
restarted.

6 Operation

42 of 162

PumpDrive

Содержание PumpDrive



































































































































































Результаты поиска

Содержание PumpDrive

Отзывы:

Похожие инструкции для PumpDrive

Бренды по названию

Популярные бренды

KSB PumpDrive, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PumpDrive

Отзывы:

Похожие инструкции для PumpDrive

Бренды по названию

Популярные бренды