Krone Comprima F 125 XC-1, Руководство по эксплуатации

Страница: 238 / 374

Placing in Storage
238
Pos: 55.1 /Überschriften/Überschriften 1/A-E/Einlagerung @ 0\mod_1197385459120_78.docx @ 19966 @ 1 @ 1
15 Placing in Storage
Pos: 55.2 /BA/Sicherheit/2. Vorangestellte Warnhinweise/WARNUNG - Nichtbeachtung der grundlegenden Sicherheitshinweise alte Form @ 254\mod_1397485793575_78.docx @ 1953347 @ @ 1
WARNING!
If the basic safety instructions are not followed, people may be seriously injured or
killed.
• To avoid accidents, the basic safety instructions in the chapter Safety must have been
read and followed, see chapter Safety "Basic safety instructions".
Pos: 55.3 /BA/Sicherheit/2. Vorangestellte Warnhinweise/WARNUNG - Nichtbeachtung der Sicherheitsroutinen alte Form @ 273\mod_1404117435996_78.docx @ 2058712 @ @ 1
WARNING!
If the safety routines are not adhered to, people may be seriously injured or killed.
• To avoid accidents, the safety routines in the chapter Safety must be read and followed,
see chapter Safety "Safety routines".
Pos: 55.4 /Überschriften/Überschriften 2/A-E/AAm Ende der Erntesaison @ 0\mod_1197385501276_78.docx @ 19985 @ 2 @ 1
15.1 At the End of the Harvest Season
Pos: 55.5 /BA/EinlagerungEinlagerung_Am Ende der Erntesaison_text_Rundballenpressen @ 468\mod_1469612812789_78.docx @ 3157097 @ @ 1
Placing the machine in storage at the end of the harvest season is the best possible way to
preserve the machine.
•
Park the machine in a dry location that is protected against the elements and away from
corrosion-promoting substances.
• Protect the tyres from external influences such as oil, grease or solar radiation.
• Clean the machine thoroughly.
Chaff and dirt attract moisture which causes steel parts to start rusting.
ATTENTION!
Damage to the machine caused by water from a high-pressure cleaner
If the water jet from a high-pressure cleaner is aimed directly at bearings and
electrics-/electronic components, these components may be damaged.
•
Do not aim the water jet from a high-pressure cleaner at bearings or electrics-/electronic
components.
•
Lubricate the machine according to the lubrication chart. Grease escaping from the bearing
positions should not be wiped away as it forms a layer offering added protection against
moisture.
• Grease the thread of setting screws and similar items.
• Remove and clean the drive chains.
• Cleaned drive chains should be oiled, mounted and re-tensioned.
• Check the chains and sprocket wheels for wear.
• Disassemble the universal shaft. Lubricate the inner tubes with grease.
• Lubricate the grease nipples on the universal joint on the universal shaft and at the bearing
rings on the protecting tubes, see chapter Maintenance – Lubrication, "Lubricating the
universal shaft".
• Lubricate the uncoated piston rods of all hydraulic cylinders liberally and insert as far as
possible.
• Wet all lever joints and bearing positions, which cannot be lubricated, with oil.
• Touch up damaged paint and preserve all uncoated areas thoroughly with rust protection
agent.
• Check all moving parts for free movement. If necessary, dismount, clean, grease and
remount.
• If parts need to be replaced, use only KRONE original spare parts.
Pos: 55.6 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1