Komatsu WA800-3E0, Руководство по эксплуатации и техническому обслуживанию

Страница: 318 / 336

HANDLING AUTO-GREASING SYSTEM
ATTACHMENTS, OPTIONS
6-8
9. Adjustment of greasing rate and injector
q
Adjust the injector to change the greasing rate for 0 - 30 hours (First step), 30 - 150 hours ((Second step)
and after 150 hours after the auto-greasing system installed.
q
Set the interval to 11.25 minutes.
The injector turns by 10 turns between the full minimum opening positions.
Up to 30Hr Up to 150Hr After 150Hr
First step Second step Third step
Injector
Interval 11.25 min 11.25 min 11.25 min
Greasing point cc/Hr
Adjustment of
injector
cc/Hr Adjustment of injector cc/Hr Adjustment of injector
SL-11 (1)
Bucket hinge
(Right and left)
49.2 Open fully 49.2
Keep at position for
first step.
49.2
Keep at position for sec-
ond step.
SL-1
(2) Front bucket link 15.6 Open fully 7.8
Open one fully. Close
one to minimum.
3.9
Close one by 5 turns
from full. Close one to
minimum.
(3) Rear bucket link 15.6 Open fully 15.6
Keep at position for
first step.
15.6
Keep at position for sec-
ond step.
(4) Bucket cylinder rod 7.8 Open fully 3.9
Close by 5 turns from
full.
1.95
Close by 2.5 turns from
position for second step.
(5)
Bucket cylinder
bottom
7.8 Open fully 3.9
Close by 5 turns from
full.
1.95
Close by 2.5 turns from
position for second step.
(6) Bell crank center 15.6 Open fully 7.8
Open one fully. Close
one to minimum.
3.9
Close one by 5 turns
from full. Close one to
minimum.
(7)
Boom cylinder rod
(Right and left)
7.8 Open fully 3.9
Close by 5 turns from
full.
3.9
Keep at position for sec-
ond step.
(8)
Boom cylinder bot-
tom
(Right and left)
7.8 Open fully 3.9
Close by 5 turns from
full.
3.9
Keep at position for sec-
ond step.
(9)
Boom pivot
(Right and left)
15.6 Open fully 15.6
Keep at position for
first step.
15.6
Keep at position for sec-
ond step.
(10)
Center hinge pin
(Upper)
7.8 Open fully 3.9
Close by 5 turns from
full.
1.95
Close by 2.5 turns from
position for second step.
(11)
Steering cylinder
bottom
(Right and left)
7.8 Open fully 3.9
Close by 5 turns from
full.
1.95
Close by 2.5 turns from
position for second step.
(12) Center support 7.8 Open fully 3.9
Close by 5 turns from
full.
1.95
Close by 2.5 turns from
position for second step.
(13)
Center hinge pin
(Lower)
7.8 Open fully 3.9
Close by 5 turns from
full.
1.95
Close by 2.5 turns from
position for second step.
(14)
Rear axle support
(Front)
15.6 Open fully 7.8
Open one fully. Close
one to minimum.
3.9
Close one by 5 turns
from full. Close one to
minimum.
(15)
Transmission
mount support
7.8 Open fully 3.9
Close by 5 turns from
full.
1.56
Close by 3 turns from
position for second step.
(16)
Rear axle support
(Cover)
15.6 Open fully 7.8
Open one fully. Close
one to minimum.
3.9
Close one by 5 turns
from full. Close one to
minimum.
(17)
Rear axle support
(Top)
15.6 Open fully 7.8
Open one fully. Close
one to minimum.
3.9
Close one by 5 turns
from full. Close one to
minimum.
(18)
Steering cylinder
rod (Right and left)
7.8 Open fully 3.9
Close by 5 turns from
full.
1.95
Close by 2.5 turns from
position for second step.