■
The commands listed in Table 7 on page 19 configure parameters only for the
current address family context.
Table 7: Commands Affecting the Current Address Family
disable-dynamic-redistribute
address family
external-paths
aggregate-address
ip route-type
auto-summary
maximum-paths
bgp dampening
network
bgp wait-on-end-of-rib
redistribute
check-vpn-next-hops
table-map
default-information originate
■
The commands listed in Table 8 on page 19 configure parameters for a peer or
peer group, regardless of address family. If the peer or peer group is activated
in more than one address family, the values are changed in all those address
families. These commands are said to apply on a per-VRF basis. In the following
example, EBGP multihop is configured for the session, but when you configure
an address family, it is not available—that is, EBGP multihop is not configurable
per address family:
host1(config-router)#
neighbor 10.1.3.4 remote-as 1234
host1(config-router)#
neighbor 10.2.3.4 ebgp-multihop 5
host1(config-router)#
address-family ipv4 multicast
host1(config-router-af)#
neighbor 10.2.3.4 ebgp-multihop ?
% Invalid input detected at '^' marker.
host1(config-router-af)#
exit-address-family
Table 8: Commands Affecting All Address Families for the Specified Peer or Peer
Group
neighbor maximum-update-size
neighbor advertisement-interval
neighbor passive
neighbor allow
neighbor password
neighbor bfd-liveness-detection
neighbor peer-type
neighbor capability
neighbor remote-as
neighbor description
neighbor rib-out disable
neighbor ebgp-multihop
neighbor shutdown
neighbor graceful-restart
neighbor site-of-origin
neighbor graceful-restart restart-time
neighbor timers
neighbor graceful-restart stalepaths-time
Basic Configuration
■
19
Chapter 1: Configuring BGP Routing
Содержание JUNOSE
