Jungheinrich ECE 118, Руководство по эксплуатации

Страница: 45 / 81

0406
.GB
E 18
5.5 Travel parameters
Z
For trucks without a display instrument (CANDIS (
o
)) the code lock parameters can
only be set by the manufacturer's service department.
The following example shows the parameter setting for the acceleration of travel
program 1 (parameter 101).
Acceleration example
– Enter the three digit parameter number (101) and confirm with the Set key (17).
– Check the LC display of the display instrument (CANDIS (
o
)) (parameter number
and current parameter value are displayed).
Z
If there is no input for approx. 5 seconds, the display switches back to showing
the operating hours.
F
If a parameter number other than the one desired is displayed, you must wait until
the operating hours are displayed again.
– Enter or change the parameter value according to the parameter list.
– Check the LCD display of the display instrument (CANDIS (
o
)), confirm with
the Set key (17).
– The LED (16) of the
o
key (21) switches briefly to a steady light and starts flashing
again after approx. 2 seconds.
Z
If the entry is incorrect, the LED (16) on the
o
key (21) flashes red. If you enter
the parameter number again the setting can be entered or changed.
Repeat the process to enter more parameters as soon as the LED (16) of the
o
key
(21) flashes. To complete the setting, press the
o
key (21).
Z
Travel is disabled while the parameters are being entered. If the setting is to be
checked in programming mode, follow this sequence:
– Select the edited travel program after entering the parameter, and confirm with
the Set key (17).
– The truck is now in travel mode and can be checked.
– To continue setting, confirm with the Set key (17) again.
Display instrument
(CANDIS)
LED (16)
o
key
LED (18)
Key 1
LED (19)
Key 2
LED (20)
Key 3
Current setting
is displayed
101 6
Green
flashing
Off Off Off
Changed setting
is displayed
101 8
Green
flashing
Off Off Off
Parameter
number
Parameter
setting
0406
.GB
E 18
5.5 Travel parameters
Z
For trucks without a display instrument (CANDIS (
o
)) the code lock parameters can
only be set by the manufacturer's service department.
The following example shows the parameter setting for the acceleration of travel
program 1 (parameter 101).
Acceleration example
– Enter the three digit parameter number (101) and confirm with the Set key (17).
– Check the LC display of the display instrument (CANDIS (
o
)) (parameter number
and current parameter value are displayed).
Z
If there is no input for approx. 5 seconds, the display switches back to showing
the operating hours.
F
If a parameter number other than the one desired is displayed, you must wait until
the operating hours are displayed again.
– Enter or change the parameter value according to the parameter list.
– Check the LCD display of the display instrument (CANDIS (
o
)), confirm with
the Set key (17).
– The LED (16) of the
o
key (21) switches briefly to a steady light and starts flashing
again after approx. 2 seconds.
Z
If the entry is incorrect, the LED (16) on the
o
key (21) flashes red. If you enter
the parameter number again the setting can be entered or changed.
Repeat the process to enter more parameters as soon as the LED (16) of the
o
key
(21) flashes. To complete the setting, press the
o
key (21).
Z
Travel is disabled while the parameters are being entered. If the setting is to be
checked in programming mode, follow this sequence:
– Select the edited travel program after entering the parameter, and confirm with
the Set key (17).
– The truck is now in travel mode and can be checked.
– To continue setting, confirm with the Set key (17) again.
Display instrument
(CANDIS)
LED (16)
o
key
LED (18)
Key 1
LED (19)
Key 2
LED (20)
Key 3
Current setting
is displayed
101 6
Green
flashing
Off Off Off
Changed setting
is displayed
101 8
Green
flashing
Off Off Off
Parameter
number
Parameter
setting