Jolly Mec I-DEA Angolo, Инструкция по установке, эксплуатации и обслуживанию

Страница: 6 / 44

6
•THE USER AND/OR OWNER OF THE PRODUCT
IS REQUIRED, IN ACCORDANCE WITH THE LAWS
IN FORCE, TO ASSIGN THE INSTALLATION AND MAINTE-
NANCE TO QUALIFIED AND SPECIALISED OPERATORS, AND
ACKNOWLEDGE THE RISKS AND HAZARDS SHOULD THEY
FAIL TO OBSERVE THIS REQUIREMENT.
•The installation of the heat generator and the relative combustion
product exhaustion system, the electrical connections, the com-
missioning and extraordinary maintenance MUST always be per-
formed by Qualified and/or Licensed Professional Technicians or
those Authorised by the Manufacturer.
•The product must be installed in accordance with the laws and
standards in force in the State, Region or Area in which the ma-
chine is installed.
•The system installer MUST issue a Declaration of compliance for
the work performed after commissioning the system, in accordance
with the laws in force related to system safety standards.
•The installation operator is responsible for the installation and is
therefore required to perform the work to top workmanship stan -
dards.
•The appliance must be connected to a combustion product exhau -
stion flue built in accordance with applicable standards and certi -
fied with a declaration of compliance.
•Should any installation defects arise during commissioning, the
Authorised Jolly-Mec Technician can refuse to endorse use of the
product for safety reasons and submit a written Servicing Report to
the User informing him that he and the Installation operator shall be
jointly liable for any damage to persons, animals or things if used.
•Before installing the machine, the customer and installation ope -
rator must ensure that the flooring on which it will be positioned
is suitably levelled and can support the weight (see CHAP.05 -
TECHNICAL DATA). If there is any doubt on the solidity of the
flooring, it is essential to have a Structural Engineer verify relative
installation feasibility.
•Only specialised and qualified personnel may work or carry out
checks inside the machine, complying with safety regulations.
•Prior to installation, the user and installer are obliged to check
that the mains electrical supply to which the machine will be con-
nected, corresponds to the voltage on the identification plate (see
par. 04.2-PRODUCT IDENTIFICATION), check that the system is
sized so as to bear the maximum load required of the product, and
also that it is equipped with all suitable safety devices to classify
the electrical system as COMPLIANT with applicable safety stan-
dards. If this is not the case, contact a Qualified Technician to
adapt the system to required standards.
•Personnel assigned to handling the machines and equipment
must always wear industrial gloves and boots.
•The Maintenance Operator must recommend the Customer to
sign an annual maintenance contract for the product, so as to
maintain the levels of safety and efficient performance of the pro -
duct.
•The Maintenance Operator must check the working hours of the
product between one maintenance intervention and another, to ve-
rify the actual work load of the stove. The actual hours of operation
shall be reset at the end of the Technical intervention and indicated
on the Servicing Report.
02.3 SAFETY REGULATIONS FOR EXTRAORDI-
NARY MAINTENANCE AND INSTALLATION
02.4 EQUIPMENT FOR OPERATORS AND MAIN-
TENANCE PERSONNEL
1 Protection headphones
2 Gloves hand protections
3 Respiratory mask
4 Face mask or goggles
5 Accident prevention boots
6 Overalls or smock
02.5 RESIDUAL RISKS
Though JOLLY MEC CAMINETTI S.p.A. does everything within
its power to produce its systems with the greatest competence
regarding safety and consulting all the directives, laws, and regu-
lations available, there are still, if minor, some residual risks during
the phases of:
•TRANSPORT AND INSTALLATION
•ELECTRICAL CONNECTIONS (Which must be done by a qua -
lified electrician)
•MAINTENANCE
Thus whoever works in these areas or is involved in
these phases must be a trained person aware of the fact
that they are “dangerous” and that it has been impossible to elimi-
nate the danger for the category of system protections.
NOTE: Removal or tampering with the protection and sa-
fety devices can be only be done voluntarily.
WARNING: removal of the protection and safety devices
(voluntary tampering) or evasion of them, may cause se-
rious injury to people! Replace the safety signals when
they become illegible or come off.
Every Operator performing maintenance on the machine, must
wear safety garments and personal protective equipment: