joke 4910880 Скачать руководство пользователя страница 50

Страница: 50 / 68

The error messages that may appear on the display are listed in the table in figure 50:

TROUBLESHOOTING, FAULTS AND MAINTENANCE

ERROR MESSAGES

ER.No

MESSAGE

CAUSE

REMEDY

SIMMER ERROR

The Laser lamp does not switch on

A. Check the fuse

B. Call CUSTOMER SERVICE

COOLANT AT

STILLSTAND

The coolant is at stillstand inside

the cooling pipes

A. Pump stopped
B.

Water dirty or cloudy

A. Check the fuse and call

CUSTOMER SERVICE

B. Check the colour of the coolant

through the openings and if

there is any sediment on the

bottom of the tank. If so,

replace the coolant and

clean the cooling system.

COOLANT

TEMPERATURE HIGH

The coolant has reached the

warning temperature (55 °C):
A. Intensive machine working

cycle

Insufficient coolant in the

storage tank

Lateral cooling fan not running

Excess dust or dirt deposited

on the heat pump

A. Wait 15 minutes, without

switching the machine off, for

the error to disappear; if it does

not, call CUSTOMER SERVICE

B. Check the coolant level in the

tank, viewing it from the side,

and top-up with distilled water

if necessary

C. Check the operation of the fan,

which, in the case of Error 01,

should run very fast, generating

considerable noise. If not, call

CUSTOMER SERVICE

D. Direct a jet of compressed air

through the openings in order

to free the heat pump of any

dust. Do not open the machine

before first having consulted

the CUSTOMER SERVICE

ELECTRONIC POWER

UNIT TEMPERATURE

HIGH

The thermostat located inside the

electronic power unit has detected

a high temperature:

Intensive machine working cycle

Dirt or dust deposited on the

rear cooling fans

Rear cooling fans not running

A. Wait a few minutes for the error

to disappear and leave the

machine to cool down for

around 20 minutes

Direct a jet of compressed air

through the openings on the

rear panel to determine whether

there is any dirt or dust

deposited on the fans. Before

opening the machine, call

CUSTOMER SERVICE

Call CUSTOMER SERVICE

INPUT RELAY

The machine is switched on but

cannot be used for welding

A. Problems with the power supply

A. Check the power supply

connections

B. Replace the power supply

CAPACITOR

VOLTAGE LOW

The electronic power unit has failed

to charge the capacitor bank

A. The generator is faulty

A. Call CUSTOMER SERVICE

Figure 50 – Error table

Содержание 4910880





































































Результаты поиска

Содержание 4910880

Отзывы:

Похожие инструкции для 4910880

Бренды по названию

Популярные бренды

joke 4910880, Руководство пользователя

Результаты поиска

Содержание 4910880

Отзывы:

Похожие инструкции для 4910880

Бренды по названию

Популярные бренды