Johnson Controls III Series Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 48

Johnson Controls III Series Скачать руководство пользователя страница 46

Appendix A—Fault and Warning Codes

44

Variable Speed Drives Series III

LIT-12012996—April 2018

www.johnsoncontrols.com

90

Drive Under Temp

Warning/Fault

• Cold weather mode is not enabled, and

unit temperature is less than -10 degree.

• Cold weather mode is enabled and Under

Temp Fault Override is not set, unit
temperature is less than -30 degree.

• Cold weather mode is enabled and Under

Temp Fault Override is not set, unit
temperature is -20~ -30 degree. The temp
<-20 degree when cold weather start
times out.

If unit temp -20 ~ -10 degree, start motor in
cold weather mode.
If unit temp <-20°, warm up unit above
-20°C for proper operation using cold
weather mode.If still < -20° when cold
weather mode times out, try higher output
voltage in cold weather mode.

91

Option Card Fault

Configurable

Fault

External supply on the DeviceNet
communication connector is not present.

Check voltage and wiring of power supply
of the DeviceNet communication.

92

External Fault 2

Configurable

Fault

Digital input is activated for external
fault input.

Check digital input settings and verify input
level, could be an external device causing
fault.

93

External Fault 3

Configurable

Fault

Digital input is activated for external
fault input.

Check digital input settings and verify input
level, could be an external device causing
fault.

103

Drive OverTemp
Warning

Warning

Drive degree greater than
(DCI_wDriveOverTempThreshold value -10
degree) and less than
DCI_wDriveOverTempThreshold value,report
drive over temperature warning.

Check the drive degree

104

Compatibility Fault

Warning

DSP firmware is not compatible with
MCB firmware

Check the DSP firmware revision

105

Compatibility Fault

Warning

Keypad firmware is not compatible with
MCB firmware

Check the keypad firmware revision

106

Compatibility Fault

Warning

IO1 card firmware is not compatible with
MCB firmware

Check the IO1 card firmware revision

107

Compatibility Fault

Warning

IO2 card firmware is not compatible
with MCB firmware

Check the IO2 card firmware revision

108

Compatibility Fault

Warning

IO3 card firmware is not compatible
with MCB firmware

Check the IO3 card firmware revision

109

Compatibility Fault

Warning

IO4 card firmware is not compatible
with MCB firmware

Check the IO4 card firmware revision

110

Compatibility Fault

Warning

IO5 card firmware is not compatible
with MCB firmware

Check the IO5 card firmware revision

111

Compatibility Fault

Warning

Profibus card firmware is not compatible
with MCB firmware

Check the Profibus card firmware revision

Table 52. Fault Codes and Descriptions, continued

Fault
Code

Fault Name

Fault Type

Default
Fault Type

Possible Cause

Remedy

«
...
44
45
46
47
48
»

Содержание III Series

















































Отзывы:

Нет отзывов