Johnson Controls 050 Скачать руководство пользователя

Страница: 53 / 166

JOHNSON CONTROLS

SECTION 3 – START-UP

FORM 100.50-NOM6

ISSUE DATE: 8/07/2017

Verifying Compressor Rotation

This unit uses scroll compressors, which

will only operate in one direction. Failure

to observe these steps could lead to com-

pressor failure.

The YORK YPAL

rooftop unit uses hermetic scroll

compressors, which only pump in one direction.

Therefore, it is necessary to verify proper rotation at

unit start-up. Operation of the compressor in the re-

verse direction will not pump, and cause the compres-

sor to cycle ON internal overload. Operating the com-

pressor in reverse for “extended” periods can result in

failure of the compressor.
To verify proper rotation, monitor the suction and

discharge pressures of the respective refrigerant cir-

cuit when the compressor cycles ON. If the discharge

pressure increases and suction pressure decreases as

the compressor cycles ON, the compressor is properly

phased and operating in the correct rotation.

Compressor Oil Level Check

The oil level can only be tested when the compressor

is running in stabilized conditions, to ensure that there

is no liquid refrigerant in the lower shell of the com-

pressor. When the compressor is running in stabilized

conditions, the oil level must be between 1/2 and 3/4 in

the oil sight glass.

Note:

at shutdown, the oil level can

fall to the bottom limit of the oil sight glass.

INITIAL START-UP

After all of the preceding checks have been completed

and the control panel has been programmed as re-

quired, the unit may be placed into operation.

1. Place the Unit Switch in the control panel to the

ON position.

2. With a demand, the supply fan will cycle ON,

and permit compressor operation if the air prov-

ing pressure switch for the supply fan has closed.

The first compressor will start. After several min

utes of operation, a flow of refrigerant will be not

ed in the sight glass, the vapor in the sight glass

will clear, and there should be a solid column of

liquid visible in the sightglass when the TXV sta-

bilizes.

4. Allow the compressor to run a short time, being

ready to stop it immediately if any unusual noise

or adverse conditions develop.

5. Check the system operating parameters by check-

ing evaporator superheat and condensing sub-

cooling. Connect a gauge manifold set to the

Schrader service valve connections on the liquid

and common suction line in the condensing sec-

tion of the unit. After the system is running and

the pressures have stabilized, measure the tem-

perature at the liquid and common suction lines

near the Schrader service valves. Calculate evap-

orator superheat and condensing subcooling. The

subcooling, should be approximately 15.0

F and

the superheat should be 12.0 °F. Repeat the above

process for each of the refrigerant systems.

6. With an ammeter, verify that each phase of the

condenser fans, compressors, supply fan, and ex-

haust fan are within the RLA/FLA as listed on the

unit data plate.

Refrigerant Charge

This rooftop unit comes fully charged from the factory

with refrigerant R-410A as standard.

TABLE 21 -

CONDENSER COIL PRESSURE DROP

YPAL050

YPAL051

YPAL060

YPAL061

33 PSIG

39 PSIG

24 PSIG

27 PSIG

Checking Superheat and Subcooling

An R-410A temperature and pressure chart lists the as-

sociated

saturation

temperature in one column, with

the associated pressure in another column. As a result,

only one temperature/pressure column is needed to

show the relationship.

Subcooling (R-410A)

When the refrigerant charge is correct, there will be no

vapor in the liquid sight glass with the system operat-

ing under full load conditions.
The subcooling temperature of each system can be cal-

culated by recording the temperature of the liquid line

at the outlet of the condenser and subtracting it from

the saturation temperature listed in

Table 22 on page

, for the corresponding discharge pressure. If the

rooftop unit does not have an access port for liquid ac-

cess, subtract the condenser coil pressure drop value

from the

Table 21 on page 53

from the discharge

pressure to determine the equivalent saturation tem-

perature.

Содержание 050







































































































































































Результаты поиска

Содержание 050

Отзывы:

Похожие инструкции для 050

Бренды по названию

Популярные бренды

Johnson Controls 050, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание 050

Отзывы:

Похожие инструкции для 050

Бренды по названию

Популярные бренды