John Bean JLT4500S Скачать руководство пользователя страница 62

Страница: 62 / 71

REV 02 OCT 2020 JLT4500-IOM-F

Check report

This report is record of all audits for operation conducted and recorded by an inspector or expert.

This lift was audited on DATE: ______________________________ and subjected to testing for operational readiness.

Describe deficiencies found (if any)

Extent of the Check:

Pending Checks (if any):

If there are (no*) concerns to limit this lift for operation. Additional verification is not required. (

* = Delete if not applicable)

Place and Date

Inspector’s Signature

Name and address in block letters

Job Description and Company

Operator or Agent

Notes on defects

Place and Date

Signature

Issues Fixed

Place and Date

Signature

Verification

This Lift has been verified on _______________________________.

The unsatisfactory performance of the first examination has not been corrected?

Содержание JLT4500S








































































Результаты поиска

Содержание JLT4500S

Отзывы:

Похожие инструкции для JLT4500S

Бренды по названию

Популярные бренды

John Bean JLT4500S, Руководство пользователя

Результаты поиска

Содержание JLT4500S

Отзывы:

Похожие инструкции для JLT4500S

Бренды по названию

Популярные бренды