John Bean JLT4500S Скачать руководство пользователя страница 6

Страница: 6 / 71

REV 02 OCT 2020 JLT4500-IOM-F

DANGER

In order to prevent risks to third parties and/or damages to things, before any operation takes place, the user shall make sure that

there are not things or persons close to the lift before starting any working cycle.

DANGER

Before using the lift, make sure that required protective apparels are used (protective gloves, goggles…).

This manual is addressed to the user of the lift and to the person who has the responsibility of its correct and safe use.

Read carefully the warnings contained in this manual, which is also supplying the indications for a correct and hazard free use of the lift.

Familiarize with the controls and the operations required for the use of the lift in emergency conditions. Always keep this manual by the lift, in

order to consult it in the event of any future possible need. The manual shall follow the lift in case it is sold.

DANGER

Immediately point out any problem or breakdown, including eventual defects detected on the control unit and/or on the hydraulic

and electric connections to the owner of the lift or to the person in charge of its safe use.

The user in charge of the lift shall be a person fit for the job and shall have a perfect knowledge of

how the system's equipment is to be used. He shall follow the instructions provided to guarantee

their safety and the safety of others

3 WORKPLACE ENVIRONMENT

Workplace environment must be clean and in orderly conditions. In particular, hazardous areas must be

duly delimited.

The field of motion of the load and of the load carrying devices shall be free of obstructions.

The work tools and materials shall not be left on the lifts (or in places where these may interfere

with its mechanical movements) or kept in places where they may fall and hence cause

accidents.

Each tool must be used exclusively for the use it was designed for

and in the most suitable way.

Never use tools that are deteriorated.

Do not clean nor touch any mechanical part while in motion.

Содержание JLT4500S








































































Результаты поиска

Содержание JLT4500S

Отзывы:

Похожие инструкции для JLT4500S

Бренды по названию

Популярные бренды

John Bean JLT4500S, Руководство пользователя

Результаты поиска

Содержание JLT4500S

Отзывы:

Похожие инструкции для JLT4500S

Бренды по названию

Популярные бренды